yellobrik
Quick
Reference
®
PVD 1800
3G SDI Frame Synchronizer
WARNING
Class 1 Laser Product
SDI Input
SDI Outputs
Fiber I/O (option)
12V Power Input
SDI Present
Power and
Prog. Settings LED
Module Settings
Module Reset
(through hole under GPI)
Analog REF IN
REF Status LED
Module LEDs
The module has several LEDs included to indicate status. Function is
described below:
SDI Present LED
= Valid SDI Signal connected
= (out) Non valid SDI signal or signal missing
REF Status LED
REF Input is bi-level or tri-level analog sync (auto detect), and will cross lock and convert the
SDI output to the REF standard if there is a “mismatch” between the SDI in and REF.
= REF is present and matches the SDI input format
= REF is present but does not match the SDI input format. The SDI
output is being converted to match REF input standard
= (out) REF signal is not present / valid
Power / Status LED
= Power OK, and no internal programmed settings are present
= Power OK, and some internal programmed settings are active*
= Power OK, but the module switch settings have been overwritten
with the
yello
GUI
application.
(Manual operation of any local switch
will revert module back to the physical switch settings, and will change
LED status back to yellow or green).
= (out) Power not present
* Some additional internal settings have been made using
yello
GUI
and the
LED indicates this by turning yellow. The module can be reset to factory default
using the
yello
GUI
application, or by using the reset switch on the side of the
module, which can be accessed though a hole with a paper-clip (or similar)
USB Port
The USB port is used for firmware updates and for PC/MAC control using
the
yello
GUI
software. Download
yello
GUI
from our website:
www.lynx-technik.com > support > downloads > yelloGUI software
Firmware updates are always provided free of charge and are available
via the
yello
GUI
.
Fiber I/O Options
The PVD 1800 can accommodate a
variety of fiber SDI I/O options which are
detailed below. These are SFP sub
modules and simply plug into the side
of the module. These can be added at
any time.
USB
(
for prog settings and
firmware updates)
GPI inputs
Delay Adjustment
Note:
We also have a selection of higher power 80km CWDM fiber options
if needed. Please visit our website or contact your LYNX Technik AG sales
representative for more details
SDI Fiber Transmitter Options
Model
Description
Power
OH-TX-1-LC / ST / SC
SFP Fiber TX - Singlemode - LC, ST or SC conn. - 10km
-5dBm (1310nm)
SDI Fiber Receiver Options
Model
Description
Sensitivity
OH-RX-1-LC / ST / SC
SFP Fiber RX - Singlemode - LC, ST or SC connector
-18dBm
SDI Fiber Transceiver Options
Model
Description
Power
Sense
OH-TR-1
SFP Fiber RX/TX - Singlemode, LC Connector - 10km
-5dBm
-16dBm
OH-TR-0-850
SFP Fiber RX/TX - Multimode, LC Connector - 300m
-5dBm
-15dBm
SDI CWDM Fiber Transmitter Options
Model
Description
Power
OH-TX-4-XXXX
CWDM SFP Fiber TX - Singlemode LC Conn. - 40km
XXXX=Wavelength. 18 according to ITU T G692.2
1270nm through 1610nm
-1dBm
SDI CWDM Fiber Transceiver Options
Model
Description
Power
Sense
OH-TR-4-XXXX
CWDM SFP Fiber RX/TX - Singlemode LC Conn. - 40km
XXXX=Wavelength. 18 according to ITU T G692.2
1270nm through 1610nm
-1dBm
-20dBm
www.lynx-technik.com
