Yeastar Technology TG400G User Manual Download

Page: 88 / 104

TG Series User Guide

88/104

gateway always respond the packets using

“SIP 404 NOT FOUND”.

’s recommended to be enabled for security.

OPTIONS Response 200

If you choose

“No”, when TG receive a

OPTION SIP packet, TG will

respond a

“404 NOT FOUND” SIP packets. If you choose, TG will

respond a

“200 OK” SIP packets.

Session-timers

Enable session-timer mode, by default it is

“yes”. If you found the call

is cut off every 15 minutes , please disable this.

Session-expires

The max refresh interval.

·Session-minse

The min refresh interval, which mustn't be shorter than 90s.

Session-refresher

Choose session-refresher, the default is Uas.

Configure IAX Settings

It is wise to leave the default setting as provided on the system. However, for a few settings, you
need to change them to suit your situation.

Navigate to

Gateway > VoIP Settings > IAX Settings

to configure the SIP general settings.

Check the description of IAX settings below.

Option

Description

UDP Port

Port used for IAX2 registrations. The default is 4569.

Bandwidth

Low/medium/high with this option you can control which codec to be

used.

Min Registration Time

Minimum duration (in seconds) of an IAX2 registration. The default is 60

seconds

Max Registration Time

Maximum duration (in seconds) of an IAX2 registration. The default is

1200 seconds.

Codecs

Enable the codec you want for IAX communication.

Configure General Preferences

Navigate to

Gateway > VoIP Settings > General Preferences

to configure global settings for the

TG gateway.

Check the description of general preferences settings below.

Summary of Contents for TG400G









































































































Search results

Summary of Contents for TG400G

Reviews:

Related manuals for TG400G

Brands by name

Popular brands

Yeastar Technology TG400G, User Manual

Search results

Summary of Contents for TG400G

Reviews:

Related manuals for TG400G

Brands by name

Popular brands