Yeastar Technology TG400G User Manual Download Page 7

Page: 7 / 104

TG Series User Guide

7/104

About This Guide

Thanks for choosing Yeastar TG Series GSM/3G/4G gateway.

This guide will help you learn how to operate and manage your TG gateway. In this guide, we
describe every detail on the functionality and configuration of the TG series gateway.

We begin by

assuming that you are interested in TG series gateway and familiar with networking and other IT
disciplines.

Products Covered

This guide explains how to configure the following Yeastar TG series gateways:



TG200



TG400



TG800



TG1600

Safety When Working with Electricity



Do not use a 3

party power adaptor.



Do not power on the device during the installation.



Do not work on the device, connect or disconnect cables when lightning strikes.

Summary of Contents for TG400G









































































































Search results

Summary of Contents for TG400G

Reviews:

Related manuals for TG400G

Brands by name

Popular brands

Yeastar Technology TG400G, User Manual

Search results

Summary of Contents for TG400G

Reviews:

Related manuals for TG400G

Brands by name

Popular brands