Yeastar Technology 16-FXS User Manual Download

Page: 77 / 87

TA1600/2400/3200 User Manual

77/87

Figure 11-7 Server Address



AES Key

If the configuration file is encrypted by AES key, you need to fill the key in this
field.



Always Apply

With No, it will compare the current configuration file with the last updated one, if
the contents are the same no update will be applied. With Yes, it will always apply
the updated configuration file.

Firmware Upgrade

TA1600/2400/3200 can be upgraded to a new firmware version via network or locally.
Users could upgrade firmware via HTTP or TFTP. Please go to

System→ System

Preferences→ Firmware Update

to do upgrade.

Notes:

If “Reset configuration to Factory Defaults” is enabled, the system will be restored
to factory default settings.

When updating the firmware, please don’t turn off the power. Or the system will
be damaged.

If you are trying to upgrade through HTTP, please make sure that your
TA1600/2400/3200 is able to visit external network, or it cannot access Yeastar

Summary of Contents for 16-FXS
























































































Search results

Summary of Contents for 16-FXS

Reviews:

Related manuals for 16-FXS

Brands by name

Popular brands

Yeastar Technology 16-FXS, User Manual

Search results

Summary of Contents for 16-FXS

Reviews:

Related manuals for 16-FXS

Brands by name

Popular brands