manualshive.com logo in svg

Yealink Yealink SIP-T42G, Administrator'S Manual

Share
Download
Yealink Yealink SIP-T42G Administrator'S Manual Download Page 24

Administrator’s Guide for SIP-T2 Series/T19(P) E2/T4 Series/CP860 IP Phones 

4

 

 

A call server is active and configured to receive and send SIP messages. 

This section lists the available physical features of SIP-T48G, SIP-T46G, SIP-T42G, SIP-T41P, 
SIP-T40P, SIP-T29G, SIP-T27P, SIP-T23P/G, SIP-T21(P) E2, SIP-T19(P) E2 and CP860 IP phones. 

SIP-T48G 

 

Physical Features: 

-

 

7” 800 x 480 pixel color touch screen with backlight 

-

 

24 bit depth color 

-

 

16 VoIP accounts, Broadsoft Validated/Asterisk

®

 Compatible 

-

 

HD Voice: HD Codec, HD Handset, HD Speaker 

-

 

26 keys including 7 feature keys 

-

 

1*RJ9 (4P4C) handset port 

-

 

1*RJ9 (4P4C) headset port 

-

 

2*RJ45 10/100/1000Mbps Ethernet ports 

-

 

1*RJ12 (6P6C) expansion module port 

-

 

4 LEDs: 1*power, 1*mute, 1*headset, 1*speakerphone 

-

 

Power adapter: AC 100~240V input and DC 5V/2A output 

-

 

Power over Ethernet (IEEE 802.3af) 

-

 

Built-in USB port, support Bluetooth headset 

-

 

Wall Mount 

Summary of Contents for Yealink SIP-T42G



































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands