Yealink W80 Administrator'S Manual Download Page 75 | Manualshive

Page: 75 / 260

background image

Administrator’s Guide for W80 DECT IP Multi-Cell System

72

Web Statistics

Web statistics is the measurement, collection, analysis and reporting of system data for purposes of understanding
and optimizing the multi-cell system. When an abnormality occurs in the system, you can preliminarily check and
locate the problem through the Statistics page.

Topics

Base Station Group
All Calls
Base Stations Calls
Handsets Calls
Abnormal Calls
Upgrade Information
DECT Signal

Base Station Group

The module of base station group shows the synchronization information among base stations. It can display the
information of up to 30 base stations.

Topics

Base Station Statistics
Cluster Graph Statistics
Viewing Base Station Group Statistics

Base Station Statistics

The properties are shown below:

Item

Description

Base Station

Name of the base station.

RPN

Radio Fixed Part Number. The base station identity allocated by the DECT system.

IP

IP address of the base station.

MAC

MAC address of the base station.

Sync Level

Sync level within the sync hierarchy.

Base Status

Synchronization status of the base station.

•

Offline

: not available.

•

Deactive

: available but not activated.

•

Active

: activated but not synchronized.

•

Active and synced

: activated and synchronized.

•

Upgrading

: firmware upgrading.

RSSI

RPN and signal value of the synchronous base.

For example, "RPN3 (-76dBm)" indicates that the current base is synchronized with the base

«
...
73
74
75
76
77
...
»

Summary of Contents for W80





































































































































































































































































Reviews:

No comments

Related manuals for W80

Brand: NEC Pages: 288

Brand: NEC Pages: 292

Brand: Panasonic Pages: 443

Brand: Xblue Networks Pages: 32

Brand: Makita Pages: 84

Brand: VTech Pages: 2

Brand: AUDIOLINE Pages: 28

Brand: JabloCom Pages: 20

Brand: AGFEO Pages: 16

Brand: Uniden Pages: 46

Brand: SwiftCam Pages: 2

Brand: Panasonic Pages: 56

Brand: Panasonic Pages: 56

Brand: Panasonic Pages: 56

Brand: ETVAX Pages: 64

Brand: Sprint Pages: 32

Brand: FLORABEST Pages: 55

Studio 4100 Plus

Brand: BT Pages: 41

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands