Yealink W80 Administrator'S Manual Download Page 68 | Manualshive

Page: 68 / 260

background image

Network Configurations

65

Values

1

-Enabled, the INVITE Contact header uses the port in the "rport" parameter but does not use the

source IP address in the "received" parameter in the Via header of server's response.

2

-Enable Direct Process, the INVITE Contact header uses the port in the "rport" parameter and uses

the source IP address in the "received" parameter in the Via header of server's response.

Default

0

Web UI

Handset & Account > Handset Registration > Add Handset/Edit > RPort

[1]

X is the account ID. X=1-100.

SIP Port and TLS Port Configuration

You can configure the SIP and TLS source ports on the phone. Otherwise, the phone uses default values (5060 for
UDP/TCP and 5061 for TLS).

If NAT is disabled, the port number shows in the Via and Contact SIP headers of SIP messages. If NAT is enabled,
the phone uses the NAT port number (and NAT IP address) in the Via and Contact SIP headers of SIP messages,
but still using the configured source port.

The following table lists the parameters you can use to configure SIP port and TLS port.

Parameter

sip.listen_port

<y0000000000xx>.cfg

Description

It specifies the local SIP port.

If it is set to 0, the phone will automatically listen to the local SIP port.

Permitted
Values

0, Integer from 1024 to 65535

Default

5060

Parameter

sip.tls_listen_port

<y0000000000xx>.cfg

Description

It specifies the local TLS listen port.

If it is set to 0, the phone will not listen to the TLS service.

Permitted
Values

0, Integer from 1024 to 65535

Default

5061

VPN

Yealink phones use OpenVPN to achieve VPN feature. To prevent disclosure of private information, tunnel end-
points must authenticate each other before a secure VPN tunnel is established. After you configure VPN feature on
the IP phone, the phone will act as a VPN client and use the certificates to authenticate with the VPN server.

Topics

OpenVPN Related Files
VPN Configuration

OpenVPN Related Files

To use OpenVPN, you should collect the VPN-related files into one archive file in .tar format and then upload this tar
file. The VPN-related files include certificates (ca.crt and client.crt), key (client.key) and the configuration file
(vpn.cnf) of the VPN client.

The following table lists the unified directories of the OpenVPN certificates and key in the configuration file (vpn.cnf)
for Yealink phones:

«
...
66
67
68
69
70
...
»

Summary of Contents for W80





































































































































































































































































Reviews:

No comments

Related manuals for W80

Brand: GE Pages: 2

Brand: Panasonic Pages: 96

Brand: Panasonic Pages: 8

Brand: GE Pages: 60

Brand: Uniden Pages: 68

CIT310 - iPhone Cordless Phone

Brand: Linksys Pages: 2

Brand: Uniden Pages: 8

Brand: GE Pages: 68

Brand: Uniden Pages: 68

Brand: Talkswitch Pages: 65

Brand: Uniden Pages: 76

Brand: GAI-Tronics Pages: 8

Brand: Excelltel Pages: 22

Brand: BELGACOM Pages: 33

Cypress Grove 19249

Brand: Hunter Pages: 2

Brand: Panasonic Pages: 32

2420 - VT Cordless Extension Handset

Brand: Gigaphone Pages: 38

Brand: GE Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands