Yealink W80 Administrator'S Manual Download Page 67

Page: 67 / 260

Administrator’s Guide for W80 DECT IP Multi-Cell System

Description

It enables or disables the media stream to be forward forcibly on the DECT manager (DM) during a
STUN/ICE call.

Note

: The value configured by this parameter takes precedence over that configured by the para-

meter “features.media_transmit.enable”.

Permitted
Values

-Disabled

-Enabled

Default

Blank

[1]

X is the account ID. X=1-100.

[2]

If you change this parameter, the phone will reboot to make the change take effect.

Keep Alive Configuration

Yealink phones can send keep-alive packets to the NAT device for keeping the communication port open.

The following table lists the parameters you can use to configure keep alive.

Parameter

account.X.nat.udp_update_enable

[1]

<MAC>.cfg

Description

It sets the type of keep-alive packets sent by phone.

Permitted
Values

-Disabled

-Default (the phone sends the corresponding packets according to the transport protocol)

-Options (the phone sends SIP OPTIONS packets to the server)

-Notify (the phone sends SIP NOTIFY packets to the server)

Default

Web UI

Handset & Account > Handset Registration > Add Handset/Edit > Keep Alive Type

Parameter

account.X.nat.udp_update_time

[1]

<MAC>.cfg

Description

It configures the interval (in seconds) at which the phone sends a keep-alive package.

Note

: It works only if “account.X.nat.udp_update_enable” is set to 1, 2 or 3.

Permitted
Values

Integer from 0 to 3600

Default

Web UI

Handset & Account > Handset Registration > Add Handset/Edit > Keep Alive Interval (Seconds)

[1]

X is the account ID. X=1-100.

Rport Configuration

Rport allows a client to request that the server sends the response back to the source IP address and port from
which the request originated. It helps the phone traverse symmetric NATs.

Rport feature depends on support from a SIP server. For more information, refer to

RFC 3581

The following table lists the parameter you can use to configure rport.

Parameter

account.X.nat.rport

[1]

<MAC>.cfg

Description

It enables or disables the phone to add the "rport" parameter in the Via header.

Permitted

-Disabled

Summary of Contents for W80





































































































































































































































































Search results

Summary of Contents for W80

Reviews:

Related manuals for W80

Brands by name

Popular brands

Yealink W80, Administrator'S Manual

Search results

Summary of Contents for W80

Reviews:

Related manuals for W80

Brands by name

Popular brands