Yealink W80 Administrator'S Manual Download Page 60 | Manualshive

Page: 60 / 260

background image

Network Configurations

57

Permitted
Values

String within 99 characters

Default

yealink

Web UI

Settings > Auto Provision > IPv4 DHCP Option Value

VLAN

The purpose of VLAN configurations on the phone is to insert a tag with VLAN information to the packets generated
by the phone. When VLAN is properly configured for the ports (Internet port and PC port) on the phone, the phone
will tag all packets from these ports with the VLAN ID. The switch receives and forwards the tagged packets to the
corresponding VLAN according to the VLAN ID in the tag as described in IEEE Std 802.3.

In addition to manual configuration, the phone also supports the automatic discovery of VLAN via LLDP, CDP or
DHCP. The assignment takes effect in this order: assignment via LLDP/CDP, manual configuration, then assign-
ment via DHCP.

Topics

LLDP Configuration
CDP Configuration
Manual VLAN Configuration
DHCP VLAN Configuration
VLAN Change Configuration

LLDP Configuration

LLDP (Linker Layer Discovery Protocol) is a vendor-neutral Link Layer protocol, which allows the phones to advert-
ise its identity and capabilities on the local network.

When LLDP feature is enabled on the phones, the phones periodically advertise their own information to the dir-
ectly connected LLDP-enabled switch. The phones can also receive LLDP packets from the connected switch and
obtain their VLAN IDs.

The following table lists the parameters you can use to configure LLDP.

Parameter

static.network.lldp.enable

[1]

<y0000000000xx>.cfg

Description

It enables or disables the LLDP feature.

Permitted
Values

0

-Disabled

1

-Enabled, the phone attempts to determine its VLAN ID through LLDP.

Default

1

Web UI

Network > Advanced > LLDP > Active

Parameter

static.network.lldp.packet_interval

[1]

<y0000000000xx>.cfg

Description

It configures the interval (in seconds) that how often the phone sends the LLDP request.

Note

: It works only if “static.network.lldp.enable” is set to 1 (Enabled).

Permitted
Values

Integer from 1 to 3600

Default

60

Web UI

Network > Advanced > LLDP > Packet Interval (1~3600s)

[1]

If you change this parameter, the phone will reboot to make the change take effect.

«
...
58
59
60
61
62
...
»

Summary of Contents for W80





































































































































































































































































Reviews:

No comments

Related manuals for W80

Brand: E-MetroTel Pages: 4

Brand: Jabra Pages: 9

Brand: Jabra Pages: 10

Brand: Uniden Pages: 6

Brand: Chamberlain Pages: 4

Brand: Furuno Pages: 2

Brand: Ericsson Pages: 2

Brand: AT&T Pages: 2

Brand: Haier Pages: 28

Brand: Motorola Pages: 37

Brand: Motorola Pages: 72

Brand: Motorola Pages: 2

Brand: Motorola Pages: 44

Brand: Motorola Pages: 21

Brand: Motorola Pages: 2

Brand: Motorola Pages: 52

Brand: Motorola Pages: 69

Brand: Motorola Pages: 41

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands