manualshive.com logo in svg

Yealink W80, Administrator'S Manual

The Westone W80 user manual is essential for harnessing the full potential of these premium-grade earphones. Get yours now for free at manualshive.com, where you can easily download the owner's manual in PDF format. Discover the in-depth features and optimize your listening experience with this comprehensive manual.

Share
Download
background image

Administrator’s Guide for W80 DECT IP Multi-Cell System

251

Provisioning Method

Modified Items

Results

related con-
figurations

• SIP server, server port, user
name, register name and so on

effect after the call is ended.

Other configurations

The configuration takes effect imme-
diately.

Central Provisioning Any configuration

The device performs auto provisioning
after the is ended.

Note

: If the call lasts for one hour, the pro-

visioning automatically quits.

Base Issue

Why doesn’t the power indicator on the base station light up?

Plug the supplied power adapter to the base station, if the power indicator doesn’t light up, it should be a hardware
problem. Please contact your vendor or the local distributor and send the problem description for help. If you cannot
get a support from them, please send a mail which includes problem description, test result, your country and
phone’s SN to

[email protected]

.

Why doesn’t the network indicator on the base station slowly flash?

It means that the base station cannot get an IP address. Try connecting the base station to another switch port, if the
network indicator still slowly flashes, please try a reset.

Handset Issues

How to check which area the handset is used for?

Go to

OK

>

Status

>

Handset

>

Area

.

Register Issue

Why cannot the handset be registered to the base station?

If the network works normally, you can check the compatibility between the base station and the handset. There are
2 sets of base stations, complied with the FCC and CE standard respectively. You can check it from the back of the
base station. There are also 2 sets of handsets, American version/European version area respectively.

The handset in the American version is compatible with FCC standard base station.

The handset in the European version is compatible with CE standard base station.

Display Issue

Why does the handset prompt the message “Not Subscribed”?

Check the registration status of your handset. If your handset is not registered to the base station, register it manu-
ally.

Why does the handset prompt the message “Not in Range” or “Out Of
Range”?

l

Ensure that the base station is properly plugged into a functional AC outlet.

l

Ensure that the handset is not too far from the base station.

Summary of Contents for W80





































































































































































































































































Reviews:

No comments

Related manuals for W80

NEC Aspire Administrator'S Manual preview
Aspire
Brand: NEC Pages: 7
NEC Aspire Quick Reference preview
Aspire
Brand: NEC Pages: 2
NEC Aspire Quick User Manual preview
Aspire
Brand: NEC Pages: 3
GE 30524 Quick Start Manual preview
30524
Brand: GE Pages: 2
Panasonic KX-NT511 Quick Reference Manual preview
KX-NT511
Brand: Panasonic Pages: 32
Panasonic KX-HDV430 Quick Start Manual preview
KX-HDV430
Brand: Panasonic Pages: 115
Panasonic DBS 576 User Manual preview
DBS 576
Brand: Panasonic Pages: 22
Panasonic GLOBARANGE BB-GT1500E Quick Manual preview
GLOBARANGE BB-GT1500E
Brand: Panasonic Pages: 10
BBK BKT-58P RU Telephone Equipment preview
BKT-58P RU
Brand: BBK Pages: 18
3Com NBX 1105 Telephone Manual preview
NBX 1105
Brand: 3Com Pages: 98
Gigaset Gigaset CX100 isdn Instructions Manual preview
Gigaset CX100 isdn
Brand: Gigaset Pages: 123
Sylvania STID991 User'S Manual And Operating Instructions preview
STID991
Brand: Sylvania Pages: 2
VTech CD1260 User Manual preview
CD1260
Brand: VTech Pages: 2
Uniden DECT2180 Guide Utilisateur preview
DECT2180
Brand: Uniden Pages: 36
AT&T 1455 User Manual preview
1455
Brand: AT&T Pages: 36
Chamberlain OTIUEX Assembly And Installation preview
OTIUEX
Brand: Chamberlain Pages: 4
Scitec 6003S Datasheet preview
6003S
Brand: Scitec Pages: 1
Makita VJ06 Instruction Manual preview
VJ06
Brand: Makita Pages: 28

Brands by name

Popular brands

Load more brands