Yealink W80 Administrator'S Manual Download Page 208

Page: 208 / 260

Call Features

205

Web UI

Features > Transfer > Blind Transfer On Hook

Parameter

transfer.on_hook_trans_enable

<y0000000000xx>.cfg

Description

It enables or disables the phone to complete the semi-attended/attended transfer through on-hook
besides the TRAN key.

Note

: Semi-attended transfer means transferring a call after hearing the ringback tone; Attended trans-

fer means transferring a call with prior consulting.

Permitted
Values

-Disabled

-Enabled

Default

Web UI

Features > Transfer > Attended Transfer On Hook

[1]

X is the account ID. X=1-100.

Conference

The Yealink phones support local conference and network conference.

Topics

Conference Type Configuration
Network Conference Configuration

Conference Type Configuration

You can specify which type of conference to establish.

The following table lists the parameter you can use to set a conference type.

Parameter

account.X.conf_type

[1]

<MAC>.cfg

Description

It configures the conference type for a specific account.

Permitted
Values

-Local Conference

-Network Conference

Default

Web UI

Handset & Account > Handset Registration > Add Handset/Edit > Conference Type

[1]

X is the account ID. X=1-100.

Network Conference Configuration

Network conference, also known as a centralized conference, provides you with the flexibility of call with multiple
participants (more than three). The phones implement network conference using the REFER method specified in

RFC 4579

. This feature depends on the support from a SIP server

For network conference, if any party leaves the conference, the remaining parties are still connected.

The following table lists the parameter you can use to configure the network conference.

Parameter

account.X.conf_uri

[1]

<MAC>.cfg

Description

It configures the network conference URI for a specific account.

Note

: It works only if “account.X.conf_type” is set to 2 (Network Conference).

Permitted
Values

SIP URI within 511 characters

Summary of Contents for W80





































































































































































































































































Search results

Summary of Contents for W80

Reviews:

Related manuals for W80

Brands by name

Popular brands

Yealink W80, Administrator'S Manual

Search results

Summary of Contents for W80

Reviews:

Related manuals for W80

Brands by name

Popular brands