Yealink W80 Administrator'S Manual Download Page 206 | Manualshive

Page: 206 / 260

background image

Call Features

203

Note:

It works only if “features.fwd.allow” is set to 1 (Enabled) and “features.fwd_mode” is set to 1

(Custom).

Permitted
Values

Integer from 0 to 20

Default

2

Web UI

Features > Forward&DND > Forward > AccountX > No Answer Forward > After Ring Time(0~120s)

Parameter

account.X.timeout_fwd.on_code

[1]

<MAC>.cfg

Description

It configures the no answer forward on code to activate the server-side no answer forward feature.

The phone will send the no answer forward on code and the pre-configured destination number (con-
figured by the parameter “account.X.timeout_fwd.target”) to the server when you activate no answer
forward feature on the phone.

Note:

It works only if “features.fwd.allow” is set to 1 (Enabled) and “features.fwd_mode” is set to 1

(Custom).

Permitted
Values

String within 32 characters

Default

Blank

Web UI

Features > Forward&DND > Forward > AccountX > No Answer Forward > On Code

Parameter

account.X.timeout_fwd.off_code

[1]

<MAC>.cfg

Description

It configures the no answer forward off code to deactivate the server-side no answer forward feature.

The phone will send the no answer forward off code to the server when you deactivate no answer for-
ward feature on the phone.

Note:

It works only if “features.fwd.allow” is set to 1 (Enabled) and “features.fwd_mode” is set to 1

(Custom).

Permitted
Values

String within 32 characters

Default

Blank

Web UI

Features > Forward&DND > Forward > AccountX > No Answer Forward > Off Code

[1]

X is the account ID. X=1-100.

Call Forward Synchronization for Server-side Configuration

Call forward synchronization feature provides the capability to synchronize the status of the call forward features
between the IP phone and the server.

If the call forward is activated in phone mode, the forward status changing locally will be synchronized to all
registered accounts on the server; but if the forward status of the specific account is changed on the server, the for-
ward status locally will be changed.

The following table lists the parameters you can use to configure call forward synchronization for server-side.

Parameter

features.feature_key_sync.enable

<y0000000000xx>.cfg

Description

It enables or disables to synchronize the feature status between the IP phone and the server.

Permitted
Values

0

-Disabled

1

-Enabled, the phone sends a SUBSCRIBE message with event “as-feature-event” to the server.

Default

0

«
...
204
205
206
207
208
...
»

Summary of Contents for W80





































































































































































































































































Reviews:

No comments

Related manuals for W80

Venture IP 480i

Brand: Aastra Pages: 12

Brand: Altigen Pages: 6

Brand: Radio Shack Pages: 24

Brand: MagicBox Pages: 44

Brand: Gigaset Pages: 28

Brand: Uniden Pages: 40

Brand: Witech Pages: 24

Brand: TechMatte Pages: 2

Brand: GADGETMONSTER Pages: 28

Brand: Honeywell Pages: 28

SILENT KHIGHT SK-FFT

Brand: Honeywell Pages: 58

Brand: Honeywell Pages: 32

Brand: Motorola Pages: 200

Brand: Motorola Pages: 8

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 10

Brand: Panasonic Pages: 28

Brand: Panasonic Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands