Yealink VC110 Administrator'S Manual Download Page 83 | Manualshive

Page: 83 / 268

background image

Configuring Network

71

To configure the network speed via web user interface:

1.

Click on Network->Advanced.

2.

Select the desired value from the pull-down list of Network Speed.

3.

Click Confirm to accept the change.

A dialog box pops up to prompt that settings will take effect after a reboot.

4.

Click Confirm to reboot the endpoint immediately.

VLAN (Virtual Local Area Network) is used to divide a physical network logically into
several broadcast domains. VLAN membership can be configured through software
instead of physically relocating devices or connections. Grouping devices with a
common set of requirements regardless of their physical location can greatly simplify
network design. VLANs can address issues such as scalability, security, and network
management.

The purpose of VLAN configurations on the endpoint is to insert a tag with VLAN
information to the packets generated by the endpoint. When VLAN is configured on the
endpoint properly, the endpoint will tag all packets with the VLAN ID. The switch
receives and forwards the tagged packets to the corresponding VLAN according to the
tag‘s VLAN ID, as described in IEEE Std 802.3.

«
...
81
82
83
84
85
...
»

Summary of Contents for VC110













































































































































































































































































Reviews:

No comments

Related manuals for VC110

Brand: Panasonic Pages: 45

Brand: Parker Pages: 58

Brand: Daewoo Pages: 35

Brand: Autotrol Pages: 8

Brand: Uniden Pages: 36

Brand: Fuslon Pages: 14

Brand: Hannlomax Pages: 2

Brand: RCA Pages: 19

Brand: Blaupunkt Pages: 69

Brand: Blaupunkt Pages: 109

Brand: Sharp Pages: 4

Brand: Sharp Pages: 32

Brand: Sharp Pages: 48

Brand: Sharp Pages: 35

Brand: Sharp Pages: 48

Brand: Sharp Pages: 32

Brand: Sharp Pages: 48

Brand: Sharp Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands