manualshive.com logo in svg

Yealink VC110, Administrator'S Manual

The Yealink VC110 is an advanced video conferencing system that offers seamless communication and collaboration. To get the most out of this powerful device, you can easily download the user manual for free from our website, ensuring a smooth user experience and optimal utilization of its features.

Share
Download
background image

Administrator‘s Guide for Yealink VC110 Video Conferencing Endpoint 

206 

Web server type determines the access protocol of the endpoint‘s web user interface. 
The endpoint supports both HTTP and HTTPS protocols for accessing the web user 
interface. HTTP is an application protocol that runs on top of the TCP/IP suite of protocols. 
HTTPS is a web protocol that encrypts and decrypts user page requests as well as the 
pages returned by the web server. Both the HTTP and HTTPS port numbers are 
configurable. 

Web server type parameters on the endpoint are described below: 

Parameter 

Description 

Configuration Method 

HTTP 

Enables or disables the user to 
access the web user interface of 
the endpoint using the HTTP 
protocol.   

Default: Enabled 

Note: If you change this 
parameter, the endpoint will 
reboot to make the change take 
effect. 

Remote Control   

Web User Interface 

HTTP Port 

Specifies the HTTP port for the 
user to access the web user 
interface of the endpoint. 

Valid Values: 1-65535 

Default: 80 

Note: Ensure that the configured 
port is not used. If you change 
this parameter, the endpoint will 
reboot to make the change take 
effect. 

Web User Interface 

HTTPS 

Enables or disables the user to 
access the web user interface of 
the endpoint using the HTTPS 
protocol.   

Default: Enabled 

Note: If you change this 
parameter, the endpoint will 
reboot to make the change take 
effect. 

Remote Control   

Web User Interface 

HTTPS Port 

Specifies the HTTPS port for the 

Web User Interface 

Summary of Contents for VC110













































































































































































































































































Reviews:

No comments

Related manuals for VC110

CAME G5000 Installation, Operation And Maintenance Manual preview
G5000
Brand: CAME Pages: 32
Fender Passport 500 Pro Instruction Manual preview
Passport 500 Pro
Brand: Fender Pages: 4
Onn ONA17AA015 Product Manual preview
ONA17AA015
Brand: Onn Pages: 11
Interroll ZoneControl Operating Manual preview
ZoneControl
Brand: Interroll Pages: 54
ATEN VK1100 User Manual preview
VK1100
Brand: ATEN Pages: 176
Elenberg MC-4090 Instruction Manual preview
MC-4090
Brand: Elenberg Pages: 36
BFT MICHELANGELO BT A 60 Installation And User Manual preview
MICHELANGELO BT A 60
Brand: BFT Pages: 84
New Rock Technologies WROC2000 User Manual preview
WROC2000
Brand: New Rock Technologies Pages: 71
LG niagara4 MultiSITE Edge 10 User Manual preview
niagara4 MultiSITE Edge 10
Brand: LG Pages: 73
Sharp XL-1000H Service Manual preview
XL-1000H
Brand: Sharp Pages: 72
JVC CA-UXG1 Service Manual preview
CA-UXG1
Brand: JVC Pages: 51
JVC CA-D301T Instructions Manual preview
CA-D301T
Brand: JVC Pages: 37
JVC CA-FSSD550 Instructions Manual preview
CA-FSSD550
Brand: JVC Pages: 27
JVC CA-UXG110 Instructions Manual preview
CA-UXG110
Brand: JVC Pages: 24
JVC CA-UXF2B Instructions preview
CA-UXF2B
Brand: JVC Pages: 2
JVC CA-UXF70MD Instructions Manual preview
CA-UXF70MD
Brand: JVC Pages: 72
JVC CA-UXF3B Service Manual preview
CA-UXF3B
Brand: JVC Pages: 58
JVC CA-MXJ70 Instructions Manual preview
CA-MXJ70
Brand: JVC Pages: 34

Brands by name

Popular brands

Load more brands