manualshive.com logo in svg

Yealink VC110, Administrator'S Manual

The Yealink VC110 is an advanced video conferencing system that offers seamless communication and collaboration. To get the most out of this powerful device, you can easily download the user manual for free from our website, ensuring a smooth user experience and optimal utilization of its features.

Share
Download
background image

Administrator‘s Guide for Yealink VC110 Video Conferencing Endpoint 

156 

3.

 

Click Confirm to accept the change. 

To configure the key tone via the remote control: 

1.

 

Select Menu->Basic. 

2.

 

Mark the radio box in the Key Tone field. 

3.

 

Press the Save soft key to accept the change. 

During a call, the endpoint will display some information and icons (such as call time, 
mute icon and recording icon) by default, you can know the call status from these 
information and icons. You can also hide these icons as needed to achieve the best 
video effects. 

Parameters of hiding icons in a call feature on the endpoint are described below: 

Parameter 

Description 

Configuration Method 

Time Icon 

Enables or disables the endpoint 
to hide call time during a call. 

 

Disabled- the endpoint does 
not display call time during 
a call. 

 

Hide with UI- the endpoint 
displays call time during a 
call, but the call time will 
hide with UI.   

 

Enabled- the endpoint 
displays call time during a 
call. 

Default: Hide with UI 

Web User Interface 

Mute Icon 

Enables or disables the endpoint 
to hide mute icon (            ) during 
a call. 

 

Disabled- the endpoint does 
not display mute icon during 
a call. 

 

Hide with UI- the endpoint 
displays mute icon during a 
call, but the mute icon will 
hide with UI.   

 

Enabled- the endpoint 

Web User Interface 

Summary of Contents for VC110













































































































































































































































































Reviews:

No comments

Related manuals for VC110

Barco CX-20 Quick Setup Manual preview
CX-20
Brand: Barco Pages: 4
S&S Northern Merlin 1000VW+ Installation, Operating And Maintenance preview
Merlin 1000VW+
Brand: S&S Northern Pages: 9
Data Aire dap4 touch User Manual preview
dap4 touch
Brand: Data Aire Pages: 137
Aastra IntelliGate 2025 User Manual preview
IntelliGate 2025
Brand: Aastra Pages: 71
Vansco DIGI-TRACK Manual preview
DIGI-TRACK
Brand: Vansco Pages: 11
T-audio LX200T User Manual preview
LX200T
Brand: T-audio Pages: 2
American Panel IC+ Manual preview
IC+
Brand: American Panel Pages: 18
TerraTec Aureon 7.1 FireWire Product Information preview
Aureon 7.1 FireWire
Brand: TerraTec Pages: 2
Polycom SolutionStation 2W User Manual/Administrator Manual preview
SolutionStation 2W
Brand: Polycom Pages: 46
Valcom VL-CONF-4 Quick Start Manual preview
VL-CONF-4
Brand: Valcom Pages: 6
Grandstream Networks UCM6304 Quick Installation Manual preview
UCM6304
Brand: Grandstream Networks Pages: 20
BFT MOOVI 30S Installation And User Manual preview
MOOVI 30S
Brand: BFT Pages: 23
BFT MOOVI ART 90 Installation Manual preview
MOOVI ART 90
Brand: BFT Pages: 8
Sony CMT-X5CD Operating Instructions preview
CMT-X5CD
Brand: Sony Pages: 2
Sony CMT-V9 Operating Instructions preview
CMT-V9
Brand: Sony Pages: 2
Sony CMT-V75BTIP Operating Instructions preview
CMT-V75BTIP
Brand: Sony Pages: 2
Sony CMT-V10IPN Operating Instructions preview
CMT-V10IPN
Brand: Sony Pages: 2
Sony CMT-SPZ50 Operating Instructions preview
CMT-SPZ50
Brand: Sony Pages: 2

Brands by name

Popular brands

Load more brands