manualshive.com logo in svg

Yealink VC110, Administrator'S Manual

The Yealink VC110 is an advanced video conferencing system that offers seamless communication and collaboration. To get the most out of this powerful device, you can easily download the user manual for free from our website, ensuring a smooth user experience and optimal utilization of its features.

Share
Download
background image

Administrator‘s Guide for Yealink VC110 Video Conferencing Endpoint 

152 

6.

 

Select the desired value from the pull-down list of Date Format. 

 

7.

 

Click Confirm to accept the change. 

To configure the time and date format via the remote control: 

1.

 

Select Menu->Basic->Date & Time. 

2.

 

Configure the desired values. 

3.

 

Press the Save soft key to accept the change. 

The time and date displayed on the LCD screen of the display device and video 
conferencing phone will change accordingly. 

The endpoint will enter the sleep mode automatically when it has been inactive for a 
period of time (the default time is 10 minutes). When the endpoint is in sleep mode, it 
can still accept incoming calls. The display device will prompt ‖No Signal‖, and the LCD 
screen of the video conferencing phone prompts ―Sleeping Press any key to resume‖. 
You can press any key on the remote control or the video conferencing phone to wake 
the endpoint up. When receiving a call, the endpoint will be woken up automatically. 

You can change the automatic sleep time via the remote control or web user interface. 
You can also press the sleep key on the remote control to make the endpoint sleep 
immediately. 

The automatic sleep time is described below: 

Parameter 

Description 

Configuration Method 

Automatic Sleep 

Time 

Configures the inactive time (in 
minutes) before the endpoint 
enter sleep mode. 

Default: 10 Min 

Note: During setup wizard, the 
automatic sleep time feature is 

Remote Control 

Web User Interface 

Summary of Contents for VC110













































































































































































































































































Reviews:

No comments

Related manuals for VC110

Zenith FFH-185A Installation And Operating Manual preview
FFH-185A
Brand: Zenith Pages: 14
ICM Controls IG-02 Operating Instruction preview
IG-02
Brand: ICM Controls Pages: 2
Panamax M4000-PRO Instructions Manual preview
M4000-PRO
Brand: Panamax Pages: 16
Jensen JDH910BT User Manual preview
JDH910BT
Brand: Jensen Pages: 13
ZheJiang Libiao Robotics LBAP-102LU-900 Instruction Manual preview
LBAP-102LU-900
Brand: ZheJiang Libiao Robotics Pages: 10
Stryker SwitchPoint Infinity 3 Operation And Maintenance Manual preview
SwitchPoint Infinity 3
Brand: Stryker Pages: 124
Hioki 3911-20 Instruction Manual preview
3911-20
Brand: Hioki Pages: 32
Daewoo AXL-125 Service Manual preview
AXL-125
Brand: Daewoo Pages: 22
QFX BT-207 Instruction Manual preview
BT-207
Brand: QFX Pages: 7
Forge Electronics COMBO MK 3 Manual preview
COMBO MK 3
Brand: Forge Electronics Pages: 10
Clearaudio Smart Phono H V2 User Manual preview
Smart Phono H V2
Brand: Clearaudio Pages: 3
ACS Compact FLASH III User Manual preview
Compact FLASH III
Brand: ACS Pages: 37
btsr DIAPERFEEDER IP54 DUOLOOP Operating Manual preview
DIAPERFEEDER IP54 DUOLOOP
Brand: btsr Pages: 57
Boss Rebel ATV22CB User Manual preview
Rebel ATV22CB
Brand: Boss Pages: 2
Cambium Networks PTP 820E Quick Installation Instructions preview
PTP 820E
Brand: Cambium Networks Pages: 16
Boss Audio Systems BASS800 User Manual preview
BASS800
Brand: Boss Audio Systems Pages: 13
Hitachi REC670 Commissioning Manual preview
REC670
Brand: Hitachi Pages: 242
Panasonic SAAK66 - MINI HES W/CD PLAYER Service Manual preview
SAAK66 - MINI HES W/CD PLAYER
Brand: Panasonic Pages: 14

Brands by name

Popular brands

Load more brands