manualshive.com logo in svg

Yealink VC110, Administrator'S Manual

The Yealink VC110 is an advanced video conferencing system that offers seamless communication and collaboration. To get the most out of this powerful device, you can easily download the user manual for free from our website, ensuring a smooth user experience and optimal utilization of its features.

Share
Download
background image

Administrator‘s Guide for Yealink VC110 Video Conferencing Endpoint 

102 

To configure H.460 firewall traversal via web user interface: 

1.

 

Click on Account->H323. 

2.

 

Select the desired value from the pull-down list of H.460 Active. 

 

3.

 

Click Confirm to accept the change. 

To configure H.460 firewall traversal via the remote control: 

1.

 

Select Menu->Advanced (default password: 0000) ->H.323. 

2.

 

Check the H.460 checkbox. 

3.

 

Press the Save soft key to accept the change. 

The video conferencing endpoint can provide efficiency and continuous communication 
for both the head office and a branch office.   

In some cases, the head office is in the WAN and lacks a VPN network, while the branch 
office is the LAN, and no port mapping is configured on its firewall. You can enable the 
intelligent firewall traversal feature, so that the head office can share content with 
branch office, or control the camera of branch office.     

The intelligent firewall traversal parameter is described below: 

Parameter 

Description 

Configuration Method 

Intelligent Firewall 

Traversal 

Enables or disables the 
intelligent firewall traversal 

Web User Interface 

Summary of Contents for VC110













































































































































































































































































Reviews:

No comments

Related manuals for VC110

Da-Lite Lectern Instruction Book preview
Lectern
Brand: Da-Lite Pages: 8
Vansco DIGI-TRACK Manual preview
DIGI-TRACK
Brand: Vansco Pages: 11
Fancom LUMINA 41 Instruction Manual preview
LUMINA 41
Brand: Fancom Pages: 51
C.S.L. VARIVAC 2006 B Instruction & Installer'S Manual preview
VARIVAC 2006 B
Brand: C.S.L. Pages: 27
EasyLine RM-208 CB.13.01 Operating And Installation Instructions preview
RM-208 CB.13.01
Brand: EasyLine Pages: 16
Stahl ET-306-A Series Operating Instructions Manual preview
ET-306-A Series
Brand: Stahl Pages: 60
Lars Thrane IRIDIUM CERTUS 100 Quick Start Manual preview
IRIDIUM CERTUS 100
Brand: Lars Thrane Pages: 4
Philips CID3283 User Manual preview
CID3283
Brand: Philips Pages: 32
Philips AZP6 Quick Start Manual preview
AZP6
Brand: Philips Pages: 2
Philips BTD1180 Specifications preview
BTD1180
Brand: Philips Pages: 3
Philips AZ2402 Brochure preview
AZ2402
Brand: Philips Pages: 2
Philips AZ1834 Specifications preview
AZ1834
Brand: Philips Pages: 3
Philips AZ1826 Specification Sheet preview
AZ1826
Brand: Philips Pages: 2
Philips DCD132/51 User Manual preview
DCD132/51
Brand: Philips Pages: 21
Philips DCC951 Instructions For Use Manual preview
DCC951
Brand: Philips Pages: 22
Philips BTM3160 User Manual preview
BTM3160
Brand: Philips Pages: 20
Philips AZ1826 User Manual preview
AZ1826
Brand: Philips Pages: 13
Philips AZ783 User Manual preview
AZ783
Brand: Philips Pages: 16

Brands by name

Popular brands

Load more brands