manualshive.com logo in svg

Yealink SIP-T42S IP, User Manual

The Yealink SIP-T42S IP phone offers a feature-rich communication experience. To get started quickly, download the free Quick Start manual from our website. Simplify setup and enjoy all the capabilities of this versatile phone. Explore our website to download the manual and unleash the power of the Yealink SIP-T42S IP.

Share
Download
background image

User Guide for the SIP-T42S IP Phone 

154 

3.

 

Click 

Confirm

 to accept the change. 

Note

 

Receiving RTP Stream 

You can configure the phone to receive a Real Time Transport Protocol (RTP) stream from the 
pre-configured multicast address(es) and channel(s) without involving SIP signaling. You can 
specify up to 31 multicast addresses and channels that the phone listens to on the network. 

Note

 

How the phone handles incoming multicast paging calls depends on Paging Barge, Ignore DND 
and Paging Priority Active parameters configured via web user interface. 

Paging Barge 

The paging barge parameter defines the priority of the voice call in progress. If the priority of an 
incoming multicast paging call is lower than that of the active call, it will be ignored 
automatically. Valid values in the Paging Barge field: 

 

1 to 31

: Define the priority of the active call, 1 with the highest priority, 31 with the lowest. 

 

Disabled

: The voice call in progress will take precedence over all incoming paging calls. 

Ignore DND 

The ignore DND parameter defines the lowest priority of multicast listening address from which 
the phone can receive an RTP stream when DND is activated. If a priority is selected from the 
pull-down list of Ignore DND, the phone will ignore incoming multicast paging calls with lower 
priorities when DND is activated in phone mode. Valid values in the Ignore DND field: 

 

1 to 31

: Define the lowest priority of the multicast listening address from which the phone 

can receive an RTP stream, 1 with the highest priority, 31 with the lowest. 

 

Disabled

: All the incoming multicast paging calls will be ignored when DND is activated in 

phone mode. 

The phone will automatically answer all incoming multicast paging calls when DND is activated 
in custom mode.

 

 

 

If G722 codec is used for multicast paging,

 

the LCD screen will display the icon            to indicate 

that high definition voice is provided.   

Default codec for multicast paging is configurable via web user interface only.

 

RTP stream is listened in the hands-free (speakerphone) mode by default. If you want to listen the 
RTP stream using the engaged audio device (speakerphone, handset or headset), contact your 
system administrator for more information. 

Fixed volume to play RTP stream for specified paging group is configurable by your system 
administrator. 

Summary of Contents for SIP-T42S IP









































































































































































































Reviews:

No comments

Related manuals for SIP-T42S IP

Unify OpenStage 40 Operating Instructions Manual preview
OpenStage 40
Brand: Unify Pages: 144
UniData Communication Systems WPU-7800 User Manual preview
WPU-7800
Brand: UniData Communication Systems Pages: 60
Uniden EXI7246B Guía De Referencia Rápida preview
EXI7246B
Brand: Uniden Pages: 48
Audiovox TDM-2500 Owner'S Operating Manual preview
TDM-2500
Brand: Audiovox Pages: 40
Orchid Telecom KS 416 System Administration Manual preview
KS 416
Brand: Orchid Telecom Pages: 25
Oricom TP170WP User Manual preview
TP170WP
Brand: Oricom Pages: 24
AGFEO AC 14 User Manual preview
AC 14
Brand: AGFEO Pages: 84
Betax PRO DBB0202 Operating Instruction preview
DBB0202
Brand: Betax PRO Pages: 26
Ultratec Compact-C User Manual preview
Compact-C
Brand: Ultratec Pages: 33
BT Diverse 6210 User Manual preview
Diverse 6210
Brand: BT Pages: 70
Philips Zenia 6825 Additional Features & Benefits preview
Zenia 6825
Brand: Philips Pages: 1
AEG Voxtel S105 Quick Start Manual preview
Voxtel S105
Brand: AEG Pages: 268
SpectraLink JPI300 Installation Manual preview
JPI300
Brand: SpectraLink Pages: 68
Radio Shack 43-1236 User Manual preview
43-1236
Brand: Radio Shack Pages: 4
iDect Digital Cordless Telephone with Answer Machine User Manual preview
Digital Cordless Telephone with Answer Machine
Brand: iDect Pages: 44
Sanyo CLT-D6220 Instruction Manual preview
CLT-D6220
Brand: Sanyo Pages: 22
Sanyo CLT-D11 Instruction Manual preview
CLT-D11
Brand: Sanyo Pages: 28
Sanyo CLT-586X Instruction Manual preview
CLT-586X
Brand: Sanyo Pages: 8

Brands by name

Popular brands

Load more brands