manualshive.com logo in svg

Yealink MeetingSpace VC800, User Manual

Share
Download
Yealink MeetingSpace VC800 User Manual Download Page 188

User Guide for the VC800 Video Conferencing System 

172 

LED Status 

Description 

The CP960 conference phone is in a call and unmuted. 

Slowly flashing red 

The CP960 conference phone is receiving an incoming 
call. 

Solid red 

The CP960 conference phone is muted. 

Fast flashing yellow 

The CPW90 is in the registration mode. 

Slowly flashing yellow 

The CPW90 has registered with the CP960 conference 
phone, but the CPW90 is out of range. 
The CPW90 has registered with the CP960 conference 
phone, but the CP960 is turned off. 

Flashing red and green 
alternately 

The CP960 conference phone is searching for the 
CPW90 which has registered with it. 

Off 

The CPW90 is in the idle mode. 

Placing the CPW90 

The CPW90 has a rubber pads on its base to prevent it from sliding. You can place the CPW90 
on a conference table. Do the following to ensure optimal voice quality: 

 

For registering to CP960 conference phone successfully, make sure the CPW90 is less than 
20 meters distant from the CP960 conference phone. 

 

Place the CPW90 on a stable surface and keep it away from obstacles so that it can 
effectively pick up sounds. 

 

Charging the CPW90 

If the CPW90 is not in use, we recommend you to charge the CPW90 even when the battery is 
full. 

Summary of Contents for MeetingSpace VC800
































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands