Yealink MeetingSpace VC200 Page 218 Administrator'S Manual Download

Page: 218 / 232

| System Maintenance |

218

Capturing the Packets in Enhanced Way

You can capture more packets in enhanced way than normal mode.

Procedure

On your web user interface, go to

Setting

Configuration

Select

Enhanced

from the drop-menu of

Pcap Type

In the

Pcap Feature

field, click

Star

t to start capturing enhanced packets.

Reproduce the issue to get stack traces.

Click

Stop

to stop capturing.

Capturing the Packets in Normal Way

Procedure

On your web user interface, go to

Setting

Configuration

Select

Normal

from the drop-menu of

Pcap Type

Configure and save the following settings:

Parameter

Description

Configuration Method

Packet Capture Device

Configure the port where you

want to capture packets:
•

WAN

—capture packets of

the wired network.

•

Ext0

—capture packets of the

CP960 conference phone

•

Wlan0

—capture packets of

the wireless network.

Default

: WAN.

Web user interface

Packet Capture Count

Configure the count of the

number of packets to capture.

Default

: 5.

Web user interface

Packet Capture Clip KB

Configure the number of bytes

(in kb) of the packet to capture.

Default

: 1024.

Web user interface

Pcap Filter Type

Configure the filter type of the

packet to capture.
The supported types are as

follows:
•

Custom

—Customize the

packet filter string.

•

SIP or H245 or H225

—

Capture SIP, H245 and H225

packets.

•

RTP

—Capture RTP packets

Default

: Custom.

Web user interface

Summary of Contents for MeetingSpace VC200









































































































































































































































Search results

Summary of Contents for MeetingSpace VC200

Reviews:

Related manuals for MeetingSpace VC200

Brands by name

Popular brands

Yealink MeetingSpace VC200, Administrator'S Manual

Search results

Summary of Contents for MeetingSpace VC200

Reviews:

Related manuals for MeetingSpace VC200

Brands by name

Popular brands