Yealink MeetingSpace VC200 Page 139 Administrator'S Manual Download

Page: 139 / 232

| Configuring Video Settings |

139

Parameter

Description

Configuration Method

Frame

Configure the maximum frame

rate of the video.
• 5fps
• 15fps
• 30fps
• 60fps—this option appears

only when you enable 60fps.

Default

: 30fps.

Web user interface

Main->Resolution

Configure the maximum

resolution of the video.
• 1080P
• 720P

Default

: 1080P.

Web user interface

Note:

If both parties do not use H.265 codec, and choose to use WDR exposure mode and 60fps, the call will

switch to auto exposure mode automatically. For more information, refer to

Adjusting the White Balance

Maximizing Monitor Video Display

You monitor may not display the entire HD image. To solve this problem, you can adjust the monitor to display entire

HD image manually. This feature is not applicable to VP59.

Procedure

Do one of the following:
• On your VCS, go to

More

Setting

Basic

Display

• On your CTP20, tap

Setting

Basic

Display

Use left or right navigation key to adjust the

Display(90%-100%)

slider.

Save the change.

Configuring the Monitor Resolution

You can specify the resolution for the monitor.

Procedure

Do one of the following:
• On your web user interface, go to

Setting

Video & Audio

Output Resolution

• On your CP960 conference phone, go to

Setting

Display

Output Resolution

Configure and save the following settings:

Summary of Contents for MeetingSpace VC200









































































































































































































































Search results

Summary of Contents for MeetingSpace VC200

Reviews:

Related manuals for MeetingSpace VC200

Brands by name

Popular brands

Yealink MeetingSpace VC200, Administrator'S Manual

Search results

Summary of Contents for MeetingSpace VC200

Reviews:

Related manuals for MeetingSpace VC200

Brands by name

Popular brands