Yealink MeetingSpace VC200 Page 111 Administrator'S Manual Download

Page: 111 / 232

| Configuring Basic Settings |

111

Showing or Hiding Icons in a Call

During a call, the system will show some information and icons (such as the call time, the mute icon and recording

icon) by default, so that you can know the call status from these information and icons. You can also hide these icons

as needed to achieve the best video effects. This feature is not applicable to VP59.

Procedure

On your web user interface, go to

Setting

General

Hide Icon in Call

Configure and save the following setting:

Parameter

Description

Configuration Method

Title Bar

Enable or disable the system to

hide the title bar during a call.
•

Show

- the system displays

the title bar.

•

Hide with UI

- the system

displays the title bar and then

hide it after 5 seconds.

•

Hide

- the system hides the

title bar.

Default

: Hide with UI.

Web User Interface

Time Icon

Enable or disable the system to

hide the call time during a call.
•

Show

- the system displays

the call time.

•

Hide with UI

- the system

displays the call time

and then hide it after five

seconds.

•

Hide

- the system hides the

title bar.

Default

: Hide with UI.

Web User Interface

Mute Icon

Enable or disable the system to
hide the mute icon (

) during

a call.
•

Show

- the system displays

the mute icon.

•

Hide with UI

- the system

displays the mute icon

and then hide it after five

seconds.

•

Hide

- the system hides the

mute icon.

Default

: Hide with UI.

Web User Interface

Summary of Contents for MeetingSpace VC200









































































































































































































































Search results

Summary of Contents for MeetingSpace VC200

Reviews:

Related manuals for MeetingSpace VC200

Brands by name

Popular brands

Yealink MeetingSpace VC200, Administrator'S Manual

Search results

Summary of Contents for MeetingSpace VC200

Reviews:

Related manuals for MeetingSpace VC200

Brands by name

Popular brands