Yealink MeetingSpace VC200 Page 110 Administrator'S Manual Download

Page: 110 / 232

| Configuring Basic Settings |

110

Hiding Heading Time

You can choose to hide the time and the date on the status bar of your monitor. This feature is not applicable to VP59.

Procedure

On your web user interface, go to

Setting

General

General Information

Hide Heading Time

Configure and save the following settings:

Parameter

Description

Configuration Method

Hide Heading Time

Enables the monitor to hide the

time and the date on the status

bar.
•

—do not display the

heading time.

•

Off

—display the heading

time.

Default

: Off.

Web user interface

Hiding the User Interface in Idle Screen

You can choose to hide the user interface when the system is idle. The monitor only displays the local video or the PC

content. This feature is not applicable to VP59.

About this task

Procedure

On your web user interface, go to

Setting

General

General Information

Hide UI in Idle Screen

Configure and save the following settings:

Parameter

Description

Configuration Method

Hide UI in Idle Screen

Enables the monitor to hides the

user interface when the system is

idle.
•

—hide the user interface.

•

Off

—display the user

interface.

Default

: Off.

Web user interface

Summary of Contents for MeetingSpace VC200









































































































































































































































Search results

Summary of Contents for MeetingSpace VC200

Reviews:

Related manuals for MeetingSpace VC200

Brands by name

Popular brands

Yealink MeetingSpace VC200, Administrator'S Manual

Search results

Summary of Contents for MeetingSpace VC200

Reviews:

Related manuals for MeetingSpace VC200

Brands by name

Popular brands