Yealink MeetingEye 400 Administrator'S Manual Download Page 238

Page: 238 / 278

| Configuring the Security Features |

238

Parameter

Description

Configuration Method

Transport

Specify the transport protocol
for SIP signaling.

The supported protocols are
as follows:

•

UDP

—it provides the

best transmission for SIP
signaling.

•

TCP

—it provides a reliable

transmission for SIP
signaling.

•

TLS

—it provides a safe

transmission for SIP
signaling. TLS is available
only when the device is
registered on a SIP server
that supports TLS.

•

DNS-NAPTR

—the device

performs the DNS NAPTR
and SRV request to find
the service type and the
port if no server port is
given.

Note

• Yealink Cloud Platform

and StarLeaf Cloud
platform cannot be
configured.

• The default value of the

Zoom/Pexip/BlueJeans/
Videxio/Custom Cloud
platform/SIP IP call is TCP.

• The default value of

EasyMeet Cloud platform
is TLS.

• The default value of the

SIP account is UDP.

• If you use TLS, you

need to upload the CA
certificate to the server for
the devices.

Web user interface

Endpoint

CTP20

Managing the Trusted Certificates List

When the system serves as a TLS client and requests a TLS connection with a server, the system
should verify the server certificate sent by the server to decide whether it is trusted based on the trusted
certificates list.

About this task

The trusted certificates list contains the default and the custom certificates.

Summary of Contents for MeetingEye 400























































































































































































































































































Search results

Summary of Contents for MeetingEye 400

Reviews:

Yealink MeetingEye 400, Administrator'S Manual, Page: 238 / 278

Search results

Summary of Contents for MeetingEye 400

Reviews: