Yazoo/Kees ZEKW42170 Operator'S Manual Download

Page: 49 / 80

English-

MAINTENANCE

Blade replacement:

•

Remove blade bolt by turning
counterclockwise.

•

Install new or re-sharpened blade with
stamped "GRASS SIDE" facing towards
ground/grass (down) or “THIS SIDE UP”
facing deck and cutter housing.

•

Install and tighten blade bolt securely.

Torque blade bolt to 45-55 ft/lbs
(60-75 Nm).

WARNING!

Blades are sharp. Protect your

hands with gloves and/or wrap
blades with a heavy cloth when

handling.

IMPORTANT INFORMATION

To ensure proper assembly, center hole in
blade must align with star on cutter
housing.

8011-671

1. Blade

2. Center hole

3. Star

4. Cutter housing

5. Blade bolt (special)

Blade attachment, principal

IMPORTANT INFORMATION

Special blade bolt is heat treated.

Replace with a Yazoo/Kees bolt if required.

Do not use lower grade hardware than
specified.

Summary of Contents for ZEKW42170

















































































Search results

Summary of Contents for ZEKW42170

Reviews:

Related manuals for ZEKW42170

Brands by name

Popular brands

Yazoo/Kees ZEKW42170, Operator'S Manual

Search results

Summary of Contents for ZEKW42170

Reviews:

Related manuals for ZEKW42170

Brands by name

Popular brands