YASKAWA VIPA System SLIO Manual Download Page 71

Page: 71 / 380

4.6 Hardware configuration - System SLIO modules

To connect System SLIO modules, the CPU has a backplane bus, which must addition-

ally to be supplied. Here up to 64 System SLIO modules can be connected.

Perform, if not already done, a hardware configuration for the CPU.

Chap. 4.5

‘Hardware configuration - CPU’ page 69

Starting with slot 1 place in the slot overview of the PROFINET IO device

‘VIPA

SLIO System’

your System SLIO modules in the plugged sequence.

Parametrize if necessary the modules and assign valid addresses, so that they can

directly be addressed.

System SLIO backplane

bus

Proceeding

VIPA System SLIO

Deployment CPU 013-CCF0R00

Hardware configuration - System SLIO modules

HB300 | CPU | 013-CCF0R00 | en | 19-30

Summary of Contents for VIPA System SLIO





























































































































































































































































































































































































Search results

Summary of Contents for VIPA System SLIO

Reviews:

Brands by name

Popular brands

YASKAWA VIPA System SLIO, Manual

Search results

Summary of Contents for VIPA System SLIO

Reviews:

Brands by name

Popular brands