YASKAWA VIPA System SLIO Manual Download Page 44

Page: 44 / 380

8pin RJ45 jack:

The RJ45 jack serves as interface to the Ethernet PG/OP channel.

This interface allows you to program respectively remote control your CPU and to

access the internal web server.

The Ethernet PG/OP channel (X1/X2) is designed as switch. This enables PG/OP

communication via the connections X1 and X2.

Configurable connections are possible.

DHCP respectively the assignment of the network configuration with a DHCP server

is supported.

Default diagnostics addresses: 2025 ... 2040

At the first commissioning respectively after a factory reset the Ethernet PG/OP

channel has no IP address. For online access to the CPU via the Ethernet PG/OP

channel, valid IP address parameters have to be assigned to this by means of your

configuration tool. This is called "initialization".

Via the Ethernet PG/OP channel, you have access to:
–

Device website, where you can find information on firmware status, connected

peripherals, current cycle times, etc.

–

OPC UA

project, which is to be created in the

OPC UA Configurator

–

WebVisu

project, which is to be created in the

SPEED7 Studio

–

PROFINET IO controller or the PROFINET I-Device.

Chap. 4.7 ‘Hardware configuration - Ethernet PG/OP channel’ page 72

Chap. 9 ‘Deployment PG/OP communication - productive’ page 214

9pin SubD jack: (isolated)

The interface supports the following functionalities, which are switch able:

MPI (default / after overall reset)
The MPI interface serves for the connection between programming unit and CPU. By

means of this the project engineering and programming happens. In addition MPI

serves for communication between several CPUs or between HMIs and CPU.

Standard setting is MPI address 2.

PtP
The RS485 interface can be switched to PtP functionality

Chap. 4.9 ‘Setting VIPA

specific CPU parameters’ page 82

. Using the

PtP

functionality the RS485 interface

is allowed to connect via serial point-to-point connection to different source res. target

systems.
The following protocols are supported:
–

ASCII

–

STX/ETX

–

3964R

–

USS

–

Modbus master (ASCII, RTU)

PROFIBUS DP (option)
The PROFIBUS functionality of this interface can be activated by configuring the sub

module X1

‘MPI/DP’

of the CPU in the hardware configuration.

Chap. 11 ‘Option:

Deployment PROFIBUS communication’ page 254

To switch the interface X3 MPI(PtP) to PROFIBUS functionality you have

to activate the according bus functionality by means of a VSC storage

media from VIPA. By plugging the VSC storage card and then an overall

reset the according functionality is activated.

Chap. 4.16 ‘Deployment

storage media - VSD, VSC’ page 111

X1/X2: Ethernet PG/OP

channel

X3: MPI(PtP) interface

VIPA System SLIO

Hardware description

Structure > Interfaces

HB300 | CPU | 013-CCF0R00 | en | 19-30

Summary of Contents for VIPA System SLIO





























































































































































































































































































































































































Search results

Summary of Contents for VIPA System SLIO

Reviews:

Brands by name

Popular brands

YASKAWA VIPA System SLIO, Manual

Search results

Summary of Contents for VIPA System SLIO

Reviews:

Brands by name

Popular brands