YASKAWA VIPA System SLIO Manual Download Page 318

Page: 318 / 380

Save, compile and transfer your project.

13.7.5

Deployment as PROFIBUS DP slave

The following section describes how to use the PROFIBUS part as an "intelligent" DP

slave on master systems. Execute the following steps:

Configure a station with a CPU with DP master mode.

Network with PROFIBUS

Configure another station with a CPU with DP slave operating mode.

Network with PROFIBUS and assign the DP slave to the DP master.

Configure the I/O areas for the slave part.

The configuration is automatically adapted to the DP master.

Save, translate and transfer the respective project into the corresponding master or

slave CPU.

Start the Siemens TIA Portal and configure a CPU.

Designate the station as "... DP master".

Integrate the modules according to the hardware configuration of the master

system.

Select the PROFIBUS interface of the master CPU and select

‘Context menu

Properties’

The

‘Properties’

dialog is shown.

Set at

interface

: Type "PROFIBUS".

Connect to PROFIBUS and preset an address (e.g. 2).

Switch at Operating mode to "DP master".

Fast introduction

Configuration of the

master part

VIPA System SLIO

Configuration with TIA Portal

TIA Portal - Option: Deployment PROFIBUS communication > Deployment as PROFIBUS DP slave

HB300 | CPU | 013-CCF0R00 | en | 19-30

318

Summary of Contents for VIPA System SLIO





























































































































































































































































































































































































Search results

Summary of Contents for VIPA System SLIO

Reviews:

Brands by name

Popular brands

YASKAWA VIPA System SLIO, Manual

Search results

Summary of Contents for VIPA System SLIO

Reviews:

Brands by name

Popular brands