YASKAWA VIPA System SLIO Manual Download Page 22

Page: 22 / 380

After mounting the whole system, to protect the backplane bus connectors at the

last module you have to mount the bus cover, now. If the last module is a clamp

module, for adaptation the upper part of the bus cover is to be removed.

2.5 Wiring

CAUTION!
Consider temperature for external cables!

Cables may experience temperature increase due to system heat dissi-

pation. Thus the cabling specification must be chosen 5°C above ambient

temperature!

CAUTION!
Separate insulation areas!

The system is specified for SELV/PELV environment. Devices, which are

attached to the system must meet theses specifications. Installation and

cable routing other than SELV/PELV specification must be separated

from the system’s equipment!

2.5.1 Wiring CPU 01xC

For wiring the CPU 01xC has removable connectors. With the wiring of the connectors a

"push-in" spring-clip technique is used. This allows a quick and easy connection of your

signal and supply lines. The clamping off takes place by means of a screwdriver.

max

30V DC

max

10A

Cross section

0.08 ... 1.5mm

(AWG 28 ... 16)

Stripping length 10mm

Use for wiring rigid wires respectively use wire sleeves. When using stranded wires you

have to press the release button with a screwdriver during the wiring.

CPU connector

Data

VIPA System SLIO

Basics and mounting

Wiring > Wiring CPU 01xC

HB300 | CPU | 013-CCF0R00 | en | 19-30

Summary of Contents for VIPA System SLIO





























































































































































































































































































































































































Search results

Summary of Contents for VIPA System SLIO

Reviews:

Brands by name

Popular brands

YASKAWA VIPA System SLIO, Manual

Search results

Summary of Contents for VIPA System SLIO

Reviews:

Brands by name

Popular brands