YASKAWA VIPA System SLIO Manual Download Page 106

Page: 106 / 380

4.14 Firmware update

You can find current firmware versions at www.vipa.com in the service area. There are

the following possibilities for the firmware update:

Firmware update online - from FW V3.0.0

Chap. 4.14.1 ‘Firmware update online’

page 107

–

Transfer of the firmware file to the CPU via the CPU web page.

–

Triggering the firmware update by means of the operating mode switch.

Firmware update via memory card

Chap. 4.14.2 ‘Firmware update via memory

card’ page 108

–

Transfer of the firmware file to a memory card.

–

The identification of a firmware file on the memory card takes place by means of a

defined naming convention.

–

After PowerON and operating mode switch in the STOP position, the firmware

update can be triggered by means of operating mode switch.

The CPU has an integrated

Device web page

that also shows information about the firm-

ware version via

‘Info’

. Here you will also find information about the required firmware

‘Package’

. With

[Expert View]

you can access the extended "Expert" overview.

Chap.

4.11.1 ‘Device web page CPU’ page 94

Name

Value

Ordering Info

013-CCF0R00

Order number of the CPU

Serial

...

Serial number of the CPU

Version

01V...

Version number of the CPU

HW Revision

CPU hardware revision

Software

3.0.0

CPU firmware version

Package

Pb000265.pkb

File name for the firmware update

Overview

Show the firmware version

via web page

Tab: ‘Info’

VIPA System SLIO

Deployment CPU 013-CCF0R00

Firmware update

HB300 | CPU | 013-CCF0R00 | en | 19-30

106

Summary of Contents for VIPA System SLIO





























































































































































































































































































































































































Search results

Summary of Contents for VIPA System SLIO

Reviews:

Brands by name

Popular brands

YASKAWA VIPA System SLIO, Manual

Search results

Summary of Contents for VIPA System SLIO

Reviews:

Brands by name

Popular brands