manualshive.com logo in svg

YASKAWA U1000 Series, Technical Manual

Share
Download
YASKAWA U1000 Series Technical Manual Download Page 274

5.7  H: Terminal Functions

274

 

YASKAWA ELECTRIC

 SIEP C710636 02B YASKAWA U1000 Technical Manual

Setting 47: Node setup

If the SI-S3 option card is connected, closing this terminal will set a node address for operation on a CANopen network.

Setting 60: DC Injection Braking command

When a DC Injection Braking command is input while the drive is stopped, DC Injection Braking operation is activated. 
When a Run command or a Jog command is input, DC Injection Braking is released. 

Refer to b2: DC Injection Braking 

on page 191

 for details on setting up the DC Injection Braking function.

The diagram below illustrates how the DC Injection Braking function works.

Figure 5.65  

Figure 5.65  DC Injection Braking Input Timing Diagram

Setting 61, 62: External Speed Search command 1, 2

These input functions can be used to enable Speed Search even if parameter b3-01 = 0 (no Speed Search at start). 

Refer 

to Speed Search Activation on page 194

 for details on how to use the input signals. 

Refer to b3: Speed Search on 

page 192

 for more about Speed Search.

Note:

Operator error oPE03 will result if both Speed Search 1 and Speed Search 2 are set to the input terminals at the same time.

Setting 63: Field Weakening

Enabled in V/f Control. When closed, Field Weakening is performed. For details, 

Refer to d6: Field Weakening and 

Field Forcing on page 242

.

Setting 67: Communication test mode

The drive has a built-in function for self-diagnosing serial communications operation. The test involves wiring the send 
and receive terminals of the RS-485/422 port together. The drive transmits data and then confirms that the 
communications are received normally. 

Refer to Self-Diagnostics on page 584

 for details on how to use this function.

Setting 6A: Drive enable

A digital input configured as a “Drive enable” (H1-



 = 6A) will prevent the drive from executing a Run command 

until the input is closed. When the input is open, the digital operator will display “dnE” to indicate that the drive is 
disabled.

If a Run command is enabled before the terminal set for “Drive enable” closes, then the drive will not run until the Run 
command is cycled (i.e., a new Run command is required). If the input is opened while the drive is running, the drive will 
stop according to the stop method set to b1-03 (

Refer to b1-03: Stopping Method Selection on page 184

).

Setting 71: Speed/Torque Control switch

Switches the drive between Torque Control and Speed Control. Torque Control is enabled when the terminal is closed, 
and Speed Control is enabled when the terminal is open. Note that parameter d5-01 must be set to 0 when using this 
function. Refer to 

d5: Torque Control on page 238

 and 

Switching Between Torque and Speed Control on page 240

.

Setting 72: Zero Servo

Used to activate the Zero Servo function that can be used to lock the rotor at a certain position. Refer to 

b9: Zero Servo 

on page 215

 for details.

Setting 75, 76: Up 2, Down 2 command

The Up 2 and Down 2 function can be used to add a bias to the frequency reference. The input programmed for 75 will 
increase the bias and the input programmed for 76 will decrease it. 

Table 5.39

 explains how the Up/Down 2 function 

works depending on the frequency reference source and parameters d4-01, d4-03, and d4-05. 

Refer to d4: Frequency 

Reference Hold and Up/Down 2 Function on page 234

 for detailed explanations of these and other Up/Down 2 related 

DC Injection braking 

command

FWD Run command

Output frequency

DC Injection
braking

DC Injection
braking

DC Injection Braking

Start Frequency

(b2-01)

OFF

OFF

OFF

OFF

ON

ON

SIEP_C710636_02B_1_0.book  274 ページ  ２０１５年１１月２５日　水曜日　午後４時５６分

Summary of Contents for U1000 Series































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands