background image

7  Troubleshooting

YASKAWA ELECTRIC

 TOBP C730600 86F YASKAWA AC Drive Option SI-T3 Installation Manual

 39

n

Minor Faults and Alarms

Keypad Display

Minor Fault Name

AEr

Station Address Error
Option is set to an address outside the allowable setting range.

Cause

Possible Solution

Minor Fault 

(H2-



 = 10)

MECHATROLINK-II 
Option is set to an address 
outside the allowable setting 
range.

Set F6-20 to an address within the specified range.

YES

Keypad Display

Minor Fault Name

CALL

Serial communication transmission error
Communication is not established.

Cause

Possible Solution

Minor Fault 

(H2-



 = 10)

Communication wiring is 
faulty.

• Check for wiring errors.
• Correct the wiring.

YES

An existing short circuit or 
communications 
disconnection

Check disconnected cables and short circuits and repair as needed.

Programming error on the 
master side.

Check communications at start-up and correct programming errors.

Communication circuitry is 
damaged.

• Perform a self-diagnostics check
• If the problem continues, replace either the control board or the 

entire drive. For instructions on replacing the control board, 
contact Yaskawa or a Yaskawa representative.

Termination resistor of the 
MEMOBUS/Modbus 
communications is not 
enabled. 

Set DIP switch S2 to the ON position to enable the termination 
resistor on a drive located at the end of a network line.

Keypad Display

Minor Fault Name

CyPo

Cycle Power to Active Parameters
Comm. Option Parameter Not Upgraded

Cause

Possible Solution

Minor Fault 

(H2-



 = 10)

Although F6-15 = 1 [Comm. 
Option Parameters Reload = 
Reload Now], the drive does 
not update the 
communication option 
parameters.

Re-energize the drive to update the communication option 
parameters.
Note: If the option software version is not compatible or if you 
install an incorrect option to the drive, it will trigger an alarm.

YES

TOBP_C730600_86F_7_0_E.fm  39 ページ  2018年12月20日 木曜日 午後6時16分

Summary of Contents for SI-T3 MECHATROLINK-II A1000 Series















































Reviews: