YASKAWA PROFINET 1000 Series Page 9 Technical Manual Download

Page: 9 / 62

4 Option Components

YASKAWA

SIEP YEACOM 07A 1000-Series Option PROFINET SI-EP3 Technical Manual

Option LED Display

The option has six LEDs:

Bi-color Status LEDs:

• Module status (MS) red/green
• Network status (NS) red/green

PROFINET LEDs:

• Network speed-10/100 yellow
• Link status and network activity-Link/Act green

The operational states of the option LEDs after the power-up diagnostic LED sequence is completed are described in

Table 3

. The states with a number in parenthesis are the number of pulses of 250 ms on, 250 ms off cycles, followed by

500 ms off, then repeating the cycle. Wait at least 2 seconds for the power-up diagnostic process to complete before
verifying LED states.

Table 3 Option LED States

Name

Indication

Operating Status

Remarks

Color

Status

MS
(visible through
drive cover)

–

OFF

Power supply OFF

Power is not being supplied to the drive.

Green ON

Option

operating

The option is operating normally and
initialization is complete.

Green

Flashing (1)

Diagnostics

Diagnostic data available.

Green

Flashing (2)

Configuration tool

Identified by a configuration tool.

Red

Default MAC or fatal error occurred.

Default MAC address has been programmed or
the option has detected an unrecoverable error.

Red

Flashing (1)

Configuration error (non-fatal)

Configuration error.

Red

Flashing (2)

No IP (non-fatal)

No IP address assigned.

Red

Flashing (3)

No station name (non-fatal)

No station name assigned.

Red

Flashing (4)

Init failure (non-fatal)

Failed to initialize module.

Green/Red

Flashing

Option self-test

The option is in self-test mode.

NS
(visible through
drive cover)

–

OFF

Offline or Power supply OFF

–

Green ON

Connected

Connection established with I/O controller and
in RUN mode.

Green

Flashing

Connected and stopped

Connection established with I/O controller and
in STOP mode.

Red

BUS fault

Unrecoverable BUS fault.

Red Flashing

(1)

Lost

communication

Host communication is temporarily lost.

Red Flashing

(2)

Lost

link

link detected to network.

10/100
(visible at
RJ45 jack)

Yellow

OFF

10 Mbps is established

–

Yellow

100 Mbps is established

–

LINK/ACT
(visible at
RJ45 jack)

Green

OFF

Link is not established

–

Green

Link is established

–

Green

Flashing

Link is established and there is network
activity

–

Summary of Contents for PROFINET 1000 Series































































Search results

Summary of Contents for PROFINET 1000 Series

Reviews:

Related manuals for PROFINET 1000 Series

Brands by name

Popular brands

YASKAWA PROFINET 1000 Series, Technical Manual

Search results

Summary of Contents for PROFINET 1000 Series

Reviews:

Related manuals for PROFINET 1000 Series

Brands by name

Popular brands