manualshive.com logo in svg

YASKAWA MOTOMAN-ES200RN, Instructions Manual, Page: 41 / 82

Share
Download
YASKAWA MOTOMAN-ES200RN Instructions Manual Download Page 41

7.2  Internal User I/O Wiring Harness and Air Lines

7-3

HW0482143

Fig. 17 (a)   Connectors for internal user I/O wiring harness and air lines

A

Connector for the external axis (Power cable):
JL05-2A18-1SC (socket connector with cap).
Prepare pin connector: JL05-6A18-1P.

Connector for the external axis (Encoder cable):
JL05-2A20-29SC (socket connector with cap).
Prepare pin connector: JL05-6A20-29P.

Connector for internal user I/O wiring harness (Casing):
JL05-2A22-14SC (socket connector with cap).
Prepare pin connector: JL05-6A22-14P.

Air inlet (air flow)
Tapped hole PT3/8 with pipe plug

Connector for internal user I/O wiring harness (Base):
JL05-2A28-21PC (pin connector with cap).
Prepare socket connector JL-05-6A28-21S.

S1

3BC

1BC

2BC

AIR

molex

molex

molex

A

View A

Key positions

Exhaust port (air flow)
Tapped hole PT3/8 with pipe plug

41/71

HW0482143

Summary of Contents for MOTOMAN-ES200RN



















































































Reviews:

No comments