YASKAWA DeviceNet SI-N3 Page 72 Technical Manual Download

Page: 72 / 76

13 Troubleshooting

YASKAWA ELECTRIC

SIEP C730600 43A YASKAWA AC Drive-Option Card DeviceNet Technical Manual

Minor Faults and Alarms

Digital Operator Display

Fault Name

oFA01

DeviceNet Option Fault (CN5-A)
DeviceNet Option is not properly connected.

Cause

Possible Solution

Problem with the connectors between the drive
and DeviceNet Option.

Turn the power off and check the connectors between the drive and DeviceNet Option.

Digital Operator Display

Fault Name

oFA30 to oFA43

DeviceNet Option Fault (CN5-A)
Communication ID error

Cause

Possible Solution

DeviceNet Option hardware fault

Replace the DeviceNet Option. Contact Yaskawa for assistance.

Operator Display

Fault Name

oFb00

DeviceNet Option Fault (CN5-B)
Non-compatible option card is connected.

Cause

Possible Solution

Non-compatible option connected to the drive.

⇒

Connect the correct option card to CN5-A.

Operator Display

Fault Name

oFb02

DeviceNet Option Fault (CN5-B)
Two of the same option cards are connected at the same time.

Cause

Possible Solution

Option cards AI-A3 or D1-A3 were connected to
the CN5-B port while an option card was already
connected to CN5-A.

⇒

Only one type of option input card AI-A3 or DI-A3 can be connected to the drive. Only this

option card for DeviceNet can be connected to CN5-A.

Operator Display

Fault Name

oFc00

DeviceNet Option Fault (CN5-C)
Non-compatible option card is connected.

Cause

Possible Solution

Non-compatible option connected to the drive.

⇒

Connect the correct option card to CN5-A.

Operator Display

Fault Name

oFc02

DeviceNet Option Fault (CN5-C)
Two of the same option cards are connected at the same time.

Cause

Possible Solution

Option cards AI-A3 or D1-A3 were connected to
the CN5-C port while an option card was already
connected to CN5-A.

⇒

Only one type of option input card AI-A3 or DI-A3 can be connected to the drive. Only this

option card for DeviceNet can be connected to CN5-A.

Digital Operator Display

Fault Name

CALL

Serial Communication Transmission Error
Communication has not yet been established.

Cause

Possible Solution

Minor Fault

(H2-

= 10)

Communication wiring or terminal resistor
connection is faulty, there is a short circuit, or
something is not connected properly.

Check for wiring errors.
Correct the wiring.
Remove and ground shorts and reconnect loose wires.

Yes

Programming error on the master side

Check communications at start-up and correct programming errors.

Communication circuitry is damaged.

Perform a self-diagnostics check.
Replace the drive if the fault continues to occur.

Summary of Contents for DeviceNet SI-N3













































































Search results

Summary of Contents for DeviceNet SI-N3

Reviews:

Related manuals for DeviceNet SI-N3

Brands by name

Popular brands

YASKAWA DeviceNet SI-N3, Technical Manual

Search results

Summary of Contents for DeviceNet SI-N3

Reviews:

Related manuals for DeviceNet SI-N3

Brands by name

Popular brands