YASKAWA 2A0001 Technical Manual Download Page 261

Page: 261 / 512

Open Loop Vector (OLV) Motor Control Method Tuning

Table 6.2 Parameters for Tuning the Drive in OLV Motor Control Method

Problem

Parameter No.

Corrective Action

Default Value

Suggested

Setting

• Poor motor torque and speed

response

• Control motor hunting and

oscillation at speeds between 10

and 40 Hz.

AFR Gain

(n2-01)

• If motor torque and speed response are too slow,

gradually decrease the setting by 0.05.

• If motor hunting and oscillation occur, gradually

increase the setting by 0.05.

<1>

0.50 to 2.00

• Poor motor torque and speed

response

• Control motor hunting and

oscillation at speeds between 10

and 40 Hz.

AFR Time Constant 1

(n2-02)

• To improve motor torque speed response,

gradually reduce this setting by 10 ms and check

the performance.

• If motor hunting and oscillation occur as a result of

load inertia, gradually increase the setting by 50 ms

and check the performance.

Note:

Ensure that n2-02 ≤ n2-03. When making

adjustments to n2-02, set C4-02 (Torque

Compensation Primary Delay Time Constant 1)

accordingly.

50 ms

50 to 2000 ms

• Overvoltage trips when

accelerating, decelerating, or

during sudden speed or load

changes.

AFR Time Constant 2

(n2-03)

• If overvoltage trips occur, gradually increase this

setting by 50 ms.

• If response is slow, gradually reduce this setting by

10 ms.

Note:

Ensure that n2-02 ≤ n2-03. When making

adjustments to n2-03, increase the value of C4-06

(Torque Compensation Primary Delay Time 2)

proportionally.

750 ms

750 to 2000 ms

Torque Compensation

Primary Delay Time

Constant 2 (C4-06)

• If overvoltage trips occur, gradually increase this

setting by 10 ms and check the performance.

• If response is slow, gradually reduce this setting by

2 ms and check the performance.

Note:

Ensure that C4-02 ≤ C4-06. When changing

C4-06 (Torque Compensation Primary Delay Time

Constant 2), increase the value of n2-03

proportionally.

150 ms

150 to 750 ms

• Poor motor torque and speed

response

• Motor hunting and oscillation.

Torque Compensation

Primary Delay Time

Constant 1

(C4-02)

• To improve motor torque speed response,

gradually reduce this setting by 2 ms and check the

performance.

• If motor hunting and oscillation occur, gradually

increase this setting by 10 ms.

Note:

Ensure that C4-02 ≤ C4-06. When making

adjustments to C4-02, increase n2-02 (AFR Time

Constant) proportionally.

20 ms

<2>

20 to 100 ms

• Poor speed response and stability

Slip Compensation

Primary Delay Time

Constant (C3-02)

• If response is slow, gradually decrease the setting

by 10 ms.

• If speed is unstable, gradually increase the setting

by 10 ms.

200 ms

<2>

100 to 500 ms

• Poor speed precision

Slip Compensation

Gain (C3-01)

• If speed is too slow, gradually increase the setting

by 0.1 ms.

• If speed is too fast, gradually decrease the setting

by 0.1 ms.

1.0

<2>

0.5 to 1.5

• Motor noise
• Control motor hunting and

oscillation occur at speeds below

10 Hz.

Carrier Frequency

Selection (C6-02)

• If there is too much motor noise, the carrier

frequency is too high.

• If motor hunting and oscillation occur at low

speeds, reduce the carrier frequency.

• The default setting for the carrier frequency

depends on the drive capacity (o2-04) and Drive

Duty Selection (C6-01).

7 (Swing PWM

0 to the default

setting

6.2 Motor Performance Fine Tuning

YASKAWA ELECTRIC SIEP C710606 18F YASKAWA AC Drive – V1000 Technical Manual

261

Troubleshooting

Summary of Contents for 2A0001

































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2A0001

Reviews:

YASKAWA 2A0001, Technical Manual, Page: 261 / 512

Search results

Summary of Contents for 2A0001

Reviews: