Yanmar ZT370 Operation Manual Download Page 7 | Manualshive

Page: 7 / 60

background image

ZT370 Operation Manual

3

ZT370 Operation Manual

SAFETY

Yanmar considers safety of great
importance and recommends that anyone
that comes into close contact with its
products, such as those who install,
operate, maintain or service Yanmar
products, exercise care, common sense
and comply with the safety information in
this manual and on the engine and
stern-drive’s safety labels. Keep the labels
from becoming dirty or torn and replace
them if they are lost or damaged. Also, if
you need to replace a part that has a label
attached to it, make sure you order the
new part and label at the same time.

DANGER

DANGER indicates a hazardous
situation which, if not avoided,

will

result in death or serious injury.

WARNING

WARNING indicates a hazardous
situation which, if not avoided,

could

result in death or serious injury.

CAUTION

CAUTION indicates a hazardous
situation which, if not avoided,

could

result in minor or moderate injury.

NOTICE

NOTICE indicates a situation which can
cause damage to the machine, personal
property and/or the environment or cause
the equipment to operate improperly.

A

This safety alert symbol
appears with most safety
statements. It means
attention, become alert,
your safety is involved!
Please read and abide by
the message that follows
the safety alert symbol.

ZT370_OM.book 3 ページ２０１３年９月２７日　金曜日　午前１０時１６分

«
...
5
6
7
8
9
...
»

Summary of Contents for ZT370





























































Reviews:

No comments

Related manuals for ZT370

Brand: Intel Pages: 78

Brand: Gan Systems Pages: 24

AR0140CS2M00AUEAH3-GEVB

Brand: ON Semiconductor Pages: 5

Brand: JETWAY Pages: 48

TA870 PLUS - SETUP 2

Brand: Biostar Pages: 67

Brand: Biostar Pages: 72

Brand: Gigabyte Pages: 44

Brand: MATSONIC Pages: 78

Brand: DTK Pages: 50

Brand: Renesas Pages: 20

VIOTECH 3100 PLUS - BIOS

Brand: Biostar Pages: 41

Brand: Ublox Pages: 25

Brand: OpenVox Pages: 29

DiskOnChip PCI-G-EVB

Brand: M-system Pages: 14

Brand: FIC Pages: 52

Brand: Digilent Pages: 17

Brand: DFI Pages: 115

Brand: JETWAY Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands