Yanmar ZT370 Operation Manual Download Page 38 | Manualshive

Page: 38 / 60

background image

MAINTENANCE

34

ZT370 Operation Manual

GENERAL INSPECTION

Inspect the stern-drive at regular intervals
to help maintain top operating
performance and correct potential
problems before they occur.

Check for loose, damaged or missing
parts, hoses and clamps. Tighten or
replace as needed.

Check the electrical connections and leads
for damage and corrosion.

Remove and inspect the propeller. If it is
badly nicked, bent or cracked, consult your
authorized Yanmar Marine dealer or
distributor.

Repair nicks and corrosion damage on
stern-drive exterior finish. Never use paint
containing copper or tin. This will damage
the stern-drive and void the warranty. Use
a high quality primer and topcoat paint
specifically designed for aluminum
outboards or stern-drives. Follow the
manufacturer’s directions for surface
preparation and application.

POWER TRIM PUMP FLUID

Power trim fluid does not require changing
unless it becomes contaminated with
water or debris. Consult your authorized
Yanmar Marine dealer or distributor if the
power trim fluid needs to be changed.

ZT370_OM.book 34 ページ２０１３年９月２７日　金曜日　午前１０時１６分

«
...
36
37
38
39
40
...
»

Summary of Contents for ZT370





























































Reviews:

No comments

Related manuals for ZT370

Brand: Yamaha Pages: 96

ASC Bridge Board

Brand: Lattice Semiconductor Pages: 25

B360 GAMING PLUS

Brand: MSI Pages: 112

Brand: Supero Pages: 86

Brand: Biostar Pages: 27

Brand: NXP Semiconductors Pages: 32

GA-Z97X-Gaming G1

Brand: Gigabyte Pages: 136

Brand: Atmel Pages: 39

Brand: Gigabyte Pages: 37

Brand: JETWAY Pages: 45

Brand: Yamaha Pages: 80

Brand: Yamaha Pages: 90

Brand: Yamaha Pages: 126

Brand: DFI Pages: 83

Brand: DFI Pages: 99

M3A78-CM - Motherboard - Micro ATX

Brand: Asus Pages: 96

Brand: Asus Pages: 116

Brand: Asus Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands