Yanmar 6LPA-STP2 Operation Manual Download Page 79

Page: 79 / 110

TROUBLESHOOTING CHART

Symptom

Probable Cause

Measure

Reference

Indicators light on the

instrument panel and

alarm sounds during

operation

Shift to low speed operation immediately, and check which indicator has come on.

Stop the engine and inspect. If no abnormality is identified and there is no problem

with operation, return to port at lowest speed and request repairs.

• Engine oil low

pressure alarm

indicator comes on

Engine oil level is low.

Check engine oil level.

Add or replace.

See Checking

the Engine Oil on

page 31

Engine oil filter clogged.

Replace engine oil filter.

Replace engine oil.

See Changing

page 59

• Fresh water (coolant)

level alarm comes on

Coolant / fresh water in coolant

recovery tank is low.

Check coolant level and

refill.

See Checking

and Adding

Engine Coolant

on page 34

• Fresh water (coolant)

high temperature

alarm comes on

Coolant / fresh water in coolant

recovery tank is low.

Check coolant level and

refill.

See Checking

and Adding

Engine Coolant

on page 34

Leakage in fresh water cooling

system causing temperature to

rise.

See your authorized

Yanmar Marine dealer or

distributor.

Contamination inside cooling

system.

See your authorized

Yanmar Marine dealer or

distributor.

Fresh water cooling pump

damaged.

See your authorized

Yanmar Marine dealer or

distributor.

• Gear oil alarm comes

Insufficient drive oil.

Check oil level and refill.

See Marine Drive

Oil on page 32

• Fuel filter alarm comes

Water level in fuel / water

separator too high.

Drain.

See Draining

Fuel Filter /

Water Separator

on page 62

• Exhaust alarm comes

Insufficient discharge of cooling

seawater.

Check that seacock is open.

Damaged seawater pump.

See your authorized

Yanmar Marine dealer or

distributor.

Faulty Warning Devices

Do not operate the engine if alarm devices are not repaired. Serious accidents may

result if abnormalities are not identified due to faulty indicators or alarm.

TROUBLESHOOTING

6LPA Series Operation Manual

Summary of Contents for 6LPA-STP2















































































































Search results

Summary of Contents for 6LPA-STP2

Reviews:

Brands by name

Popular brands

Yanmar 6LPA-STP2, Operation Manual

Search results

Summary of Contents for 6LPA-STP2

Reviews:

Brands by name

Popular brands