Yanmar 6LPA-STP2 Operation Manual Download Page 56

Page: 56 / 110

Keep a Log of Engine Hours and

Daily Checks

Keep a log of the number of hours the engine

is run each day and a log of the daily checks

performed. Also note the date, type of repair

(e.g., replaced alternator), and parts used

for any service needed between the periodic

maintenance intervals. Periodic

maintenance intervals are every 50, 125,

250, 500, 1000 and 1250 engine hours.

Failure to perform periodic maintenance will

shorten the life of the engine.

Yanmar Replacement Parts

Yanmar recommends that you use genuine

Yanmar parts when replacement parts are

needed. Genuine replacement parts help

ensure long engine life.

Tools Required

Before you start any periodic maintenance

procedure, make sure you have the tools

you need to perform all of the required tasks.

Ask Your Authorized Yanmar

Marine Dealer or Distributor For

Help

Our professional service technicians have

the expertise and skills to help you with any

maintenance or service related procedures.

PERIODIC MAINTENANCE

6LPA Series Operation Manual

Summary of Contents for 6LPA-STP2















































































































Search results

Summary of Contents for 6LPA-STP2

Reviews:

Brands by name

Popular brands

Yanmar 6LPA-STP2, Operation Manual

Search results

Summary of Contents for 6LPA-STP2

Reviews:

Brands by name

Popular brands