Yanmar 6LPA-STP2 Operation Manual Download Page 43

Page: 43 / 110

Checking the Remote Control

Handle

Check the operation of the remote control

handle and ensure it moves smoothly. If it is

hard to operate, grease the joints of the

remote control cable and lever bearings. If

the lever is too loose, adjust the remote

control cable. See Checking and Adjusting

Remote Control Cables on page 65.

Checking the Alarm Indicators

Check the instruments and alarm indicators

at regular intervals.

Preparing Fuel, Oil and Coolant in

Reserve

Prepare sufficient fuel for the day’s

operation. Always store engine oil and

coolant in reserve (for at least one refill) on

board, to be ready for emergencies.

Checking the Wiring Connectors

See your authorized Yanmar Marine dealer

or distributor.

Tightening All Major Nuts and Bolts

See Tightening Fasteners on page 51 or

see your authorized Yanmar Marine dealer

or distributor.

BEFORE YOU OPERATE

6LPA Series Operation Manual

Summary of Contents for 6LPA-STP2















































































































Search results

Summary of Contents for 6LPA-STP2

Reviews:

Brands by name

Popular brands

Yanmar 6LPA-STP2, Operation Manual

Search results

Summary of Contents for 6LPA-STP2

Reviews:

Brands by name

Popular brands