manualshive.com logo in svg

Yamato Pure Line WL320A, Instruction Manual

Share
Download
Yamato Pure Line WL320A Instruction Manual Download Page 24

21 

4.Operation Method 

Pre-start preparation and checks

 

 

Be sure to check again before use.   

（

1

）

Confirmation of water feed 

    ・

Confirm that the feed water hose is firmly connected.   

    ・

Open the faucet.   

    ・

Confirm that the connection of feed water hose is free from water leakage.   

（

2

）

Confirmation of power supply 

    ・

Check if the power cord is connected to the appropriate socket outlet.   

・

Confirm that the power cord is inserted to the depth of main body power cord socket outlet.   

Operation method

 

 

Upon completion of preparation, start operation as follows.

 

 

Power application

 

Electric leakage breaker 

 

 

 

 

 

 

Operation panel (initial display)

 

 

 

Operation panel (POWER key ON)

 

 

 

 

 

①

  Set  the  electric  leakage  breaker  on  the 

right side of main body to “ON

（｜）

.”

 

 

 

 

 

 

●

Initial display for 4 seconds 

●

Only  the  water  quality  unit  lamp  ON  in    4 

seconds

 

 

 

 

 

 

 

 

 

②

  Press the POWER key. 

 

●

The water quality is displayed in the Water 

Quality Display.

 

 

 

 

○  

ON
り 

OFF
り 

ｌ 

Summary of Contents for Pure Line WL320A


















































Reviews:

No comments

Brands by name

Popular brands

Load more brands