Yamato Pure Line WE200 Instruction Manual Download

Page: 18 / 55

2. PRE-OPERATION PROCEDURES

Installation

14. Run initial wash for reverse osmosis membrane (after unit delivery and after

each time membrane is replaced)

①

Remove  the  four  retaining  screws  from
the  right  cover  of  main  unit  and  remove
cover.  Turn  the  initial  wash  selector
switch to

“ON”.

②

Turn ELB

“ON” (

｜

), then press and hold

PUSH.

●

appears in water quality

display.

●

flashes

information

display.

③

Press and hold PUSH again and initial
wash

begins.

※

Remaining

water

volume (in

ℓ

) used for initial wash will

appear and be counted down.

●

appears in water quality

display

●

flashes in information

display

④

A buzzer sounds when initial wash has
finished.

●

appears in water quality

display

●

flashes in information display

⑤

Be sure to turn the initial wash selector
to

“OFF”.

※

Normal operation cannot be performed
with the initial wash selector switch

“ON”.

⑥

Press POWER to complete the process.
Replace the cover.

※

Press and hold CLR to stop initial wash while in progress. In this case, mode will skip to

⑥

※

If a power loss occurs during initial wash, mode shifts to

②

when power is restored. Start

initial wash again, from the beginning.

②

③

⑥

Initial wash selector switch

①

Summary of Contents for Pure Line WE200
























































Search results

Summary of Contents for Pure Line WE200

Reviews:

Related manuals for Pure Line WE200

Brands by name

Popular brands

Yamato Pure Line WE200, Instruction Manual

Search results

Summary of Contents for Pure Line WE200

Reviews:

Related manuals for Pure Line WE200

Brands by name

Popular brands