manualshive.com logo in svg

Yamato IN604W, Instruction Manual, Page: 50 / 66

Share
Download
Yamato IN604W Instruction Manual Download Page 50

 

 

47 

 

Operation Method 

Set the Refrigerator Operation Mode 

 

1 

Select the item in function menu 

  Check that the power in turned on. 

 

 

 

FUNCTION

 

 

 

 

 

 

TROUBLE

 

ENTER

 

CANCEL

 

REF mode 

 

Cont 

 

 

 

 

 

 

①

  Press  the  FUNCTION  key.    The  function  menu 

starts  and  the  Sub  Display  displays  the  items.   
Select the item using the FUNCTION key. 

 

 

②

  Display  the  "REF  mode"  and  press  the  ENTER 

key. 

  Press the CANCEL key to cancel the function menu. 

2 

Select mode 

 

REF mode 

Cont 

 

 

↓

 

REF mode 

Cycle 

 

 

↓

 

REF mode 

Stop 

 

 

 

 

①

  The "

" (cursor) goes out and the mode currently 

selected  blinks  instead.    Display  the  "Cont",   
"Cycle" or "Stop" using the "

▼▲

". 

3 

Set refrigerator operation mode 

 

 

 

 

TROUBLE

 

ENTER

 

CANCEL

 

REF mode 

 

Cycle 

 

 

 

 

 

①

  Press  the  ENTER  key.    The  refrigerator 

operation mode is decided and the function menu 
selection screen is displayed. 

  The  refrigerator  continues  to  operate  if  the  setting 

temperature  is  set  to  44.0

℃

  or  below  in  the 

continuous operation. 

  It  repeats  12-minute  operation  and  12-minute  halt 

condition in the cycle operation. 

Summary of Contents for IN604W



































































Reviews:

No comments