Yamaha YZF-R6T Owner'S Manual Download Page 86

Page: 86 / 111

PERIODIC MAINTENANCE AND MINOR REPAIR

6-40

EAU24360

Front wheel

EAU34591

To remove the front wheel

WARNING

EWA10820

●

It is advisable to have a Yamaha
dealer service the wheel.

●

Securely support the motor-
cycle so that there is no danger
of it falling over.

1. Loosen the wheel axle pinch bolts,

the axle bolt, and then the brake
caliper bolts.

2. Lift the front wheel off the ground

according to the procedure on
page 6-39.

3. Remove the brake hose holder

and reflector on each side by re-
moving the bolt and nut.

4. Remove the brake caliper on each

side by removing the bolts.

5. Remove the axle bolt, push the

wheel axle out from the left side,
and then remove the wheel.

CAUTION:

ECA11050

Do not apply the brake after the
brake calipers have been removed,
otherwise the brake pads will be
forced shut.

EAU34530

To install the front wheel

1. Lift the wheel up between the fork

legs.

2. Insert the wheel axle.
3. Lower the front wheel so that it is

on the ground.

4. Install the brake calipers by install-

ing the bolts, and then tightening
them to the specified torque.

1. Front wheel axle pinch bolt

1. Brake hose holder
2. Bolt and nut

3. Brake caliper bolt

4. Brake caliper
5. Axle bolt

6. Reflector

1. Wheel axle

U5SL12E0.book Page 40 Monday, August 9, 2004 10:51 AM

Summary of Contents for YZF-R6T
















































































































Search results

Summary of Contents for YZF-R6T

Reviews:

Related manuals for YZF-R6T

Brands by name

Popular brands

Yamaha YZF-R6T, Owner'S Manual

Search results

Summary of Contents for YZF-R6T

Reviews:

Related manuals for YZF-R6T

Brands by name

Popular brands