Yamaha YP125R Service Manual Download

Page: 386 / 498

FUEL TANK

7-3

EAS26630

REMOVING THE FUEL TANK

1. Extract the fuel in the fuel tank through the

fuel tank filler hole with a pump.

2. Remove:

• Fuel hose connector cover “1”

3. Remove:

• Fuel hose “2”

NOTICE

ECA37P1023

• Be sure to disconnect the fuel hose by

hand. Do not forcefully disconnect the
hose with tools.

• Although the fuel has been removed from

the fuel tank, be careful when removing the
fuel hose, since there may be fuel remain-
ing in it.

• Do not disconnect the fuel hose from the

fuel hose connector. Disconnect the con-
nector from the fuel pump.

TIP

Before removing the hose, place a few rags in
the area under where it will be removed.

4. Remove:

• Fuel sender “1”

TIP

Remove the fuel sender with the fuel sender
wrench “2”.

5. Remove:

• Fuel tank

TIP

To remove the fuel tank, lower the radiator “1”.

NOTICE

ECA37P1021

When removing the fuel tank, be sure not to
pull forcefully on the radiator hoses “2”.

EAS37P1071

CHECKING THE FUEL PRESSURE

1. Check:

• Pressure regulator operation

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Remove the fuel hose connector cover “1”,

and then remove the fuel hose “2” from the
fuel pump.

NOTICE

ECA37P1024

Although the fuel has been removed from
the fuel tank, be careful when removing the
fuel hose, since there may be fuel remaining
in it.

TIP

Before removing the hose, place a few rags in
the area under where it will be removed.

b. Connect the pressure gauge “3” and fuel

pressure adapter “4”.

Fuel sender wrench

90890-11098

Summary of Contents for YP125R



















































































































































































































































































































































































































































































































Search results

Summary of Contents for YP125R

Reviews:

Related manuals for YP125R

Brands by name

Popular brands

Yamaha YP125R, Service Manual

Search results

Summary of Contents for YP125R

Reviews:

Related manuals for YP125R

Brands by name

Popular brands