Yamaha YP125R Service Manual Download

Page: 378 / 498

THERMOSTAT (YP250R)

6-11

EAS26450

CHECKING THE THERMOSTAT

1. Check:

• Thermostat

Does not open at 80.5–83.5 °C (176.9–182.3
°F)

→

Replace.

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Suspend the thermostat “1” in a container “2”

filled with water.

b. Slowly heat the water “3”.
c. Place a thermometer “4” in the water.
d. While stirring the water, observe the thermo-

stat and thermometer’s indicated tempera-
ture.

TIP

If the accuracy of the thermostat is in doubt, re-
place it. A faulty thermostat could cause serious
overheating or overcooling.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

2. Check:

• Thermostat cover

Cracks/damage

→

Replace.

EAS26460

INSTALLING THE THERMOSTAT

1. Install:

• Thermostat

TIP

Install the thermostat with its breather hole “a” in
the position shown in the illustration.

2. Fill:

• Cooling system

(with the specified amount of the recom-
mended coolant)
Refer to “CHANGING THE COOLANT” on
page 3-32.

3. Check:

• Cooling system

Leaks

→

Repair or replace any faulty part.

A. Fully closed
B. Fully open

Summary of Contents for YP125R



















































































































































































































































































































































































































































































































Search results

Summary of Contents for YP125R

Reviews:

Related manuals for YP125R

Brands by name

Popular brands

Yamaha YP125R, Service Manual

Search results

Summary of Contents for YP125R

Reviews:

Related manuals for YP125R

Brands by name

Popular brands