manualshive.com logo in svg

Yamaha YP125R, Service Manual

The Yamaha YP125R Owner's Manual is a comprehensive guide that provides detailed instructions and information about the operation and maintenance of the Yamaha YP125R. With our user-friendly website, users can easily download this manual for free, ensuring a worry-free ownership experience. Visit manualshive.com to access your free manual today.

Share
Download
background image

V-BELT AUTOMATIC TRANSMISSION (YP250R)

5-91

* Apply Shell BT grease 3® (Yamaha grease G 90793-40016).

15

Spacer

4

For installation, reverse the removal proce-
dure.

 

Yamaha grease G

90793-40016

Removing the V-belt, primary sheave and secondary sheave

Order

Job/Parts to remove

Q’ty

Remarks

LS

LS

LS

LS

LT

LT

E

*

(4)

11

14

15

12

13

9

New

New

New

10

2

1

3

8

7

4

(4)

6

5

22 Nm (2.2 m

•

kgf, 16 ft

•

Ibf)

T.R.

60 Nm (6.0 m

•

kgf, 43 ft

•

Ibf)

T.R.

80 Nm (8.0 m

•

kgf, 58 ft

•

Ibf)

T.R.

3 Nm (0.3 m

•

kgf, 2.2 ft

•

Ibf)

T.R.

Summary of Contents for YP125R



















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for YP125R

JDbug GS300 Owner'S Manual preview
GS300
Brand: JDbug Pages: 8
Velotric Thunder 1 Quick Start Manual preview
Thunder 1
Brand: Velotric Pages: 15
Razor Kiddie Owner'S Manual And Safety Handbook preview
Kiddie
Brand: Razor Pages: 4
Smart Wheel SMARTkick X7 8.5" User Manual preview
SMARTkick X7 8.5"
Brand: Smart Wheel Pages: 10
TVS Jupiter Fi Owner'S Manual preview
Jupiter Fi
Brand: TVS Pages: 58
Capin Billy's Whiz Bang Owner'S Manual preview
Whiz Bang
Brand: Capin Billy's Pages: 44
Yamaha VITY XC125E Owner'S Manual preview
VITY XC125E
Brand: Yamaha Pages: 76
Yamaha VINO125 Owner'S Manual preview
VINO125
Brand: Yamaha Pages: 76
Yamaha VINO YJ50RAT Owner'S Manual preview
VINO YJ50RAT
Brand: Yamaha Pages: 67
Yamaha VINO YJ50RAS Owner'S Manual preview
VINO YJ50RAS
Brand: Yamaha Pages: 67
Yamaha T max Technical Manual preview
T max
Brand: Yamaha Pages: 45
Yamaha VINO YJ50RAR Owner'S Manual preview
VINO YJ50RAR
Brand: Yamaha Pages: 74
Yamaha VINO XC50X Owner'S Manual preview
VINO XC50X
Brand: Yamaha Pages: 80
Yamaha VINO XC50Z Owner'S Manual preview
VINO XC50Z
Brand: Yamaha Pages: 84
Yamaha VINO XC50V Owner'S Manual preview
VINO XC50V
Brand: Yamaha Pages: 80
Yamaha SLIDER EW50N Owner'S Manual preview
SLIDER EW50N
Brand: Yamaha Pages: 66
Yamaha RAZZ SH50L Owner'S Manual preview
RAZZ SH50L
Brand: Yamaha Pages: 65
Yamaha VERSITY 300 VP300 Owner'S Manual preview
VERSITY 300 VP300
Brand: Yamaha Pages: 84

Brands by name

Popular brands

Load more brands