Yamaha YP125R Service Manual Download

Page: 282 / 498

V-BELT AUTOMATIC TRANSMISSION (YP125R)

5-37

• Install the clutch carrier nut “2” with its tapered

side “a” facing the clutch carrier.

EAS37P1037

INSTALLING THE V-BELT

1. Install:

• V-belt “1”
• Secondary sheave assembly “2”

NOTICE

ECA37P1004

Do not allow grease to come in contact with
the V-belt or secondary sheave assembly.

TIP

• Install the V-belt with the printed arrow mark on

the V-belt facing in the direction shown in the il-
lustration.

• Install the V-belt onto the primary sheave side.

2. Tighten:

• Clutch carrier nut “1”

TIP

While holding the clutch carrier with the sheave
holder “2”, tighten the clutch carrier nut with the
locknut wrench “3”.

3. Install:

• Clutch housing “1”
• Spacer
• Secondary sheave nut “2”

TIP

While holding the clutch housing with the sheave
holder “3”, tighten the secondary sheave nut.

Clutch spring holder

90890-01337

Clutch spring holder arm

90890-01464

Clutch carrier nut

90 Nm (9.0 m·kgf, 65 ft·lbf)

Sheave holder

90890-01701

Primary clutch holder

YS-01880-A

Locknut wrench

90890-01348
YM-01348

Secondary sheave nut

60 Nm (6.0 m·kgf, 43 ft·lbf)

Sheave holder

90890-01701

Primary clutch holder

YS-01880-A

Summary of Contents for YP125R



















































































































































































































































































































































































































































































































Search results

Summary of Contents for YP125R

Reviews:

Related manuals for YP125R

Brands by name

Popular brands

Yamaha YP125R, Service Manual

Search results

Summary of Contents for YP125R

Reviews:

Related manuals for YP125R

Brands by name

Popular brands