manualshive.com logo in svg

Yamaha YFZ45YSSH, Owner'S Manual, Page: 133 / 154

Share
Download
Yamaha YFZ45YSSH Owner'S Manual Download Page 133

8-44

8

2. Connect the positive battery lead first, then

connect the negative battery lead by installing
their bolt. 

NOTICE:

 When installing the bat-

tery, the main switch must be off, and the
positive lead must be connected before
the negative lead.

 [ECB01111]

3. Install the battery holding plate by installing

the bolts.

4. Install the seat. (See page 4-10.)

EBU29962

Replacing the fuse

The fuse holder is located under the seat. (See
page 4-10.)
If the fuse is blown, replace it as follows.

1. Turn the key to “

” (off) and turn off all elec-

trical circuits.

NOTICE

ECB00641

To prevent accidental short-circuiting, turn off
the main switch when checking or replacing a
fuse.

 

1. Positive battery lead (red)
2. Negative battery lead (black)

2

1

1. Fuse
2. Spare fuse

1

2

UBW260E0.book  Page 44  Thursday, May 12, 2016  2:28 PM

Summary of Contents for YFZ45YSSH



























































































































































Reviews:

No comments